Cartridge guitar bridge

From DDL Wiki

Jump to: navigation, search
CAD Rendering of Stratocaster Guitar with Prototype 3 Bridge Installed (Click to Enlarge)
CAD Rendering of Stratocaster Guitar with Prototype 3 Bridge Installed (Click to Enlarge)

Contents

Executive Summary

The Product

Electric Guitar bridges are metal assemblies that anchor the strings to the body of the guitar. In many electric guitars, these bridges are on pivots, which allow you to create a tremolo effect by pushing on the bridge. The two main designs for electric guitar bridges are the Fender Bridge (1950’s) and the Floyd Rose Bridge (1980’s). The Fender is affordable, while the Floyd Rose is expensive and feature rich.

The Guitarist

Electric guitarists depend on their guitars staying in tune. They also need to be able to quickly change a guitar string if it breaks. The Fender bridge offers poor tuning stability, and strings are difficult to change. The Floyd Rose offers excellent tuning stability, but strings are next to impossible to change.

The Market

Guitarist can be roughly divided into two groups, professional guitarists and amateur guitarists. Amateur guitarists make up the majority of the market. They are concerned with bridges that are easy to use, and that are low costs. Professional guitarists are concerned with bridges with excellent tuning stability, and quick changing strings, adjustability, and are not concerned about cost.

The Idea

Our design is based around a string mounted into a cartridge. The cartridge attaches to a special bridge. Cartridges are easy to install and remove, simplifying string changes. Because the strings are securely and permanently mounted into the cartridges, tuning stability is excellent.

The Final Design

Our final design is targeted towards amateur guitarists. It is made from only 5 distinct parts, many cast out of aluminum for low cost. It offers excellent tuning stability, and ease of changing strings, at the cost of adjustability. We have a complete working prototype on display. The next step in our project is to begin showing our design to guitar manufacturers who might be interested in using the design on their economy model guitars.

Final Design

Concept Design

The Cartridge guitar bridge is an attempt to make a low cost guitar bridge with quality and functionality comparable to competing high-end models. The unique design features a cartridge that combines the string and saddle as one piece, which is easy to attach and remove and greatly reduces the amount of time to change a broken string. The saddle slides on and off of the bridge with twin rails, and is held in place by string tension and contact forces. Since the string is embedded in the saddle and the saddle has only a minute range of motion, the tuning stability of the cartridge model is as good or better than most high end bridges. Conversely, the design of our model is mechanically simple and would be easy to produce at a very low cost.

Comparison to Other Designs

There are many guitar bridge designs on the market today, and many more that were patented but never saw much use. In our comparisons we will focus on two specific designs, the Fender (a very common low-cost bridge, which has the majority share on the low end for tremolo bridges), and the Floyd Rose (a more high-end model which features better tuning capabilities but is more complex and much more expensive).

Standard guitar strings feature a ball end at one end of the string which is used to hold the string in place in the bridge. Our design uses a string that is die-cast into the saddle, reducing unwanted movements but increasing cost.

The Fender bridge is the basic bridge for an electric tremolo guitar. It uses standard strings, which are fed in through the back of the guitar into the sustain block. the saddles are attached with one spring and screw, and two additional screws are used to set the height but do not attach. the string is not connected to the saddle but rests in a notch on the top, the string tension holds the saddle in position. This causes some slight shifting when the tremolo is activated and the tension is lost.

The Floyd Rose is what we have studied as a high-end guitar bridge. it is far more complex than the Fender, and this is reflected in the higher manufacturing costs. The dominant feature of the Floyd Rose is its ability to clamp strings in place, enhancing its ability to keep its tune through multiple tremolo uses. the downside of this is that it takes a long time to change strings. The complex locking mechanism also makes tuning more difficult and time consuming.

A final design we consider is the Floyd Rose Speedloader. This modified Floyd Rose bridge uses custom strings with ball ends at both sides and offers the tuning stability of the Floyd Rose without the difficulty in restringing the guitar. The downside is that it costs even more than the Floyd Rose, putting it out of the range of many beginning guitarists.

Differences from Final Design

Our final design attempts to combine all of the best aspects of the sample models we studied. We take the principle of the Speed Loader for quick and easy string replacement as a positive feature of out design. We maintain the simple and easy to manufacture quality of the Fender bridge with a simple die-cast design. By having out strings integral to the saddles, we eliminate most of the points for movement in a manner similar to the Floyd Rose. The things that we did not use are high costs and complex assemblies.

Justification for Rail Design

Originally, we planned to create new, triangular rail for our final design, replacing the double round rails. The triangular rails would reduce the part count, since they would be cast onto the base plate. We decided against using the triangular rails. Cast triangular rails would have made casting the bridge very difficult, since they are a convex shape, and would require very complicated molds. The tolerances on cast rails were also too high for comfort. Our final design is very dependent on the close tolerance of the rails for its tuning stability. The tolerance for the rail itself is 0.001in, while the hole is 0.003in. This allows a maximum of 0.003 in of give in the rail, which results in our exceptional tuning stability. Casting would not be able to achieve these close fits, resulting in a less than secure mate between the saddle and the base plate. This would have seriously affected the tuning stability. If the error was to the thicker side, the saddles might not fit on the bridge at all, or would require too much force to install. This would impact the user experience and perceived quality.

We feel that although the rails add extra parts and assembly steps to our design, the end result justifies the extra cost, since it gives us our exceptional tuning stability, and ease of string changing. These two properties represent the main appeal of our design.

Design Changes from Prototype 3

The majority of the design changes from Prototype 3 involve manufacturing. While Prototype 3 contains a mix of hand machined and CNC machined parts, most of the parts on the final design will be cast out of aluminum. The saddle design is also slightly changed. This change simply reflects the fact that our mass produced saddles will be specially made with custom ends, while our prototype saddles adapt currently existing strings to fit our bridge.

The materials selection will also change slightly. Our prototype designs use several parts from our Fender bridge which are made of cast steel. Our final design will use mostly aluminum parts for weight and cost purposes. Several difficult to manufacture items, such as the screws, whammy bar, and springs will still be purchased. These parts are compatible with the standard Fender bridge.

CAD

Full CAD Drawings of our production model are available here. Image:Guitar Production Model.JPG

Bill of Materials

Table 1: Bill of Materials

Unless otherwise noted, parts sourced from external vendors use vendor's photo.

Part Number Name Qty. Function Material Manufacturing Process Image Engineering Drawing Vendor Info
1 Base Plate 1 Main plate that provides mounting surfaces and holes for all other parts. Aluminum Cast and Drilled Not Applicable
2 Sustain Block 1 Connects base plate to springs, provides leverage, provides vibrating mass for increased guitar sustain. Aluminum Cast and Drilled Not Applicable
3 Cartridges 6 Provides mounting point for string. Secures string to bridge. Aluminum Cast and Drilled Not Applicable
4 Rails 12 Allows mounting of cartridges to main bridge assembly. Aluminum Extruded and Cut Not Applicable
5 Whammy Bar 1 Lever for using Tremolo Bridge 18-8 Stainless Steel Extruded and Machined Not Applicable Stewart MacDonald 1515
6 Tremolo Spring 3 Provides restoring force for Tremolo Bridge Stainless Steel Extrusion Not Applicable Stewart MacDonald 1513
7 #6 Panhead Phillips 1 Inch Wood screw 6 Attaches Bridge to Guitar 18-8 Stainless Steel Thread Rolling Not Applicable Stewart MacDonald 3349
8 4-40 x 0.25" Flathead Philips Screw 3 Attaches sustain block to base plate. 18-8 Stainless Steel Thread Rolling Not Applicable McMaster-Carr 91771A106

Market Research

Daddy's Junky Music in Burlington MA (Click to Enlarge)
Daddy's Junky Music in Burlington MA (Click to Enlarge)

When examining the market potential for our product, it’s most important to see how similar products are faring currently. The most similar product currently on the market is the Floyd Rose Speedloader, which uses special strings to make stringing the Floyd Rose bridge easier. The ‘genuine’ Floyd Rose bridge listed online was priced at roughly 250 dollars. In comparison, a standard Fender bridge is priced at around 70 dollars. Additionally, the Speedloader strings are priced at between 9 and 12 dollars for 6 strings. In comparison, standard guitar strings sell for between 4 and 6 dollars for a pack of six, though the prices for both can vary if the strings are bought in bulk.
The market for our product would most likely exist in between the price points of the two bridges. It would most likely be to our advantage to price the product towards the end of the Fender bridge. The high end market is most likely already taken by the Floyd Rose and existing products, and is also less likely to invest in another technology if they see no reason to. Additionally, our product is mechanically simpler than the Floyd Rose, and the smaller number of parts makes it easier to produce less expensively.
Another solid reason to aim toward the low cost end of the market is that the main mechanical feature of our bridge is its ease of restringing. This is not a feature of the standard Floyd Rose, and therefore less experienced guitar players are less likely to know about the Speedloader feature’s availability. Advertising ease of restringing along with the ability to keep tune will help sell the product to novice guitar players. The availability of the Floyd Rose Speedloader is important to acknowledge because it shows that a product can sell even if it requires specialized strings. The strings for our bridge will most likely sell in the same price range as the Speedloader strings, though it’s probably possible to sell them for a bit less. The fact that strings are a repeat purchase makes it very important to price correctly, as the strings may very well make more money than the bridges themselves. The difference in price between our strings and the Speedloader strings will probably be determined by manufacturing cost rather than a different profit margin.
Ultimately, the product is unlikely to fare well in a market that is fairly saturated without the backing of a guitar manufacturer. Floyd Rose gained a lot of notoriety on behalf of his product when Eddie Van Halen started using it. This advertising got Floyd Rose offers to license his bridge technology, and this is what really got the design its exposure. In our case, it’s doubtful celebrity advertisers will fall into our laps, but going and seeking a guitar company interested in our design may be the best way to approach the issue of marketing. A company like Fender may be interested in our design, as their two primary competitors already have products available aimed towards maintaining tunability: Gibson with their Robot guitar, and Ibanez with their licensed Floyd Rose bridges.
Our bridge would be most successful if priced similarly to a Fender bridge, or slightly higher. A product will sell more if priced lower, and we believe we can still make a profit in this range due to the mechanical simplicity of our design. With few parts that can be manufactured fairly cheaply, our bridge should undercut even the Fender bridge in cost, since it has a higher part count and an equal number of unique pieces. Even the presence of unique strings shouldn't be a large issue if the strings can be priced within the range of preexisting products.
Floyd Rose’s design is successful, though its market share is still relatively low. Most likely, for our bridge design to succeed, backing of a major guitar company will be necessary. From earlier investigations, there are many patents for different bridge and string attachment mechanisms for guitars. Despite this, the majority of them are not seen in the market. For our design to succeed, the interest of an established company is likely the only way to gain the necessary exposure for the design to pay off. Given the right presentation and the right backer, our design has the right combination of better performance and simpler design to earn a place in the guitar market.

QFD

Image:Hoq1.JPG
Image:Hoq2.JPG

Conclusions

Using Quality Function deployment (QFD) to analyze some of our design decisions helped us make some important conclusions regarding our design and how it relates to similar designs on the market. The two most important characteristics of the design were how much the guitar would go out of tune, and how quickly strings could be changed. Based on how it affects the performance of the bridge and the guitar overall, the detuning of the guitar was the most important factor in the design. This changed our design philosophy slightly, and the manufacture of prototypes 2 and 3 focused more on fit and string stability than easy movement and restringing. This was also influenced by some research into the Floyd Rose Speedloader, a bridge design that can be restrung much more quickly than other designs on the market.
When compared to other designs on the market, our design has the best combination of traits as opposed to other designs. Because we considered all of the consumer needs in our design process, our bridge rates fairly highly on most of them. The other bridge designs, on the other hand, tend to be very strong in only a few areas. For instance, the Floyd Rose Speedloader holds tune very well and makes string changes very easy, but is both the most expensive bridge out of the ones we compared, and also requires a guitar to be built with the bridge, giving it the lowest score for compatibility with existing guitars. This comparison reinforces that our design offers a good compromise between performance, and complexity that would lead to higher cost.

User Data

Initial User Survey

We began our design project by conducting a user survey of 10 guitarists. We asked them about what features they liked and disliked about their electric guitars. From this data, we identified several major problem areas. These included:

  • Tuning Stability
  • String Changing Difficulty
  • Musicality of Trem Effect
  • Tuning of one string affects tuning of other strings (on Floyd Rose)

From these areas, we created a number design ideas to solve various permutations of these problems.

Design Ideas

Linear Bridge
The Linear Bridge Design.  Annotated Version.  Illustration by Jeremy Ozer
The Linear Bridge Design. Annotated Version. Illustration by Jeremy Ozer

Our first idea was a linear bridge. This bridge creates a vibrato effect by moving horizontally (with respect to the guitar body), instead of rotating. Instead of pivots and tension springs, the linear bridge would fill the bridge cavity with a high-strength track, a tremolo mounted on a "cart" on the track, and either compression or tension springs to return the bridge to pitch after the user releases the lever.

The linear bridge addresses the non-linearity we discovered in the string frequency vs. tremolo angle function that we derived in the first design [1]. It would also address the tuning stability issues, as the track and cart setup would return it its exact starting position much better than a pivot system, and would not wear out nearly as fast. The linear bridge would be easy to manufacture, because the actual bridge plate and saddles do not need to be changed from current designs (either the Fender or Floyd Rose). The current bridge plates and saddles could be made to bolt right on to the linear track. Installation is also improved for the linear bridge. With the rotational bridge designs, installing the springs is a difficult (or even dangerous) task. The linear bridge would have the springs integrated into the unit, and installing the bridge would never require the user to touch them.

Digital Bridge
The Digital Bridge Design.  Annotated Version.  Illustration by Jeremy Ozer
The Digital Bridge Design. Annotated Version. Illustration by Jeremy Ozer

The digital bridge is an "outside the box" solution to the problems of standard tremolo designs, but one that addresses most of the issues far better than conventional solutions. Instead of using a mechanical system to change the tension of the strings, which is fraught with unpredictable factors and non-linearities, our digital bridge uses a digital signal processor (DSP) to change the pitch of the sound without ever mechanically adjusting the strings. The user controls the digital bridge in the same way he would a standard tremolo bridge. A lever is located next to the bridge which the user pushes down to lower the pitch of the strings. The lever is connected to a digital rotary encoder, which is connected to a DSP chip located in the tremolo cavity. The DSP changes the pitch of the bridge in proportion to the lever, emulating the function of a regular bridge.

The digital bridge addresses most of the issues of current bridge designs. Since the pitch change is accomplished digitally, the string pitches are always in exact proportion to each other, making the digital bridge the most musical design alternative we created. Because the physical bridge is fixed, not on any sort of pivot, tuning stability is not an issue at all. The cost and manufacturability of the digital bridge is very similar to that of current designs. The physical bridge is much simpler than a regular tremolo bridge, and the circuitry is relatively simple and not expensive to create. The only point at which the digital bridge is worse than current designs is installation. The guitar would have to be modified in order to accept the new bridge. This is not an issue when the guitar is being built with the digital bridge, but it would be a problem for users looking to retrofit their guitars with a new bridge.

Cartridge Bridge
The Cartridge Bridge Design.  Annotated Version.  Illustration by Jeremy Ozer
The Cartridge Bridge Design. Annotated Version. Illustration by Jeremy Ozer

The cartridge bridge works by eliminating standard string saddles, and instead features string "cartridges" that mount to the bridge base plate. The cartridge has a standard string, with a saddle built into one end instead of a ball end. The saddle would slide into and lock onto the bridge base plate, and the string would be secure and ready to be tuned up.

The cartridge system mainly addresses the issue that modern bridges are exceptionally hard to change the strings on. The cartridge system would allow you to quickly remove the old saddle cartridge and snap on a new one in seconds. Since the strings are securely mounted in the cartridges, the tuning stability will be better than conventional Fender bridges, and on par with more expensive Floyd Rose designs. The cartridges would contain pre-stretched strings, and would be precisely calibrated for string height and intonation, both of which would also improve tuning stability. The system would be easy to manufacture and inexpensive to buy, since most of the bridge parts are very similar to current Fender bridge designs. The cartridges would be inexpensive, made mainly of plastic with a few metal pieces. A pack of string cartridges would only cost a few dollars more than a pack of standard strings.

"Raccoon Trap" Saddles
The "Raccoon Trap" Saddle Design.  Annotated Version.  Illustration by Jeremy Ozer
The "Raccoon Trap" Saddle Design. Annotated Version. Illustration by Jeremy Ozer

The "raccoon trap" saddles would be drop in replacements for either Fender or Floyd Rose saddles. Instead of conventional string securing methods (usually a simple clamp or simply holding the ball end of the string), the raccoon trap saddle would integrate an internal one-way clamp (like a zip-tie). The string can slide easily into the saddle, but when the string is pulled on, the clamp digs in and the string will not move. The string could be released by pushing a button on the saddle.

The "raccoon trap" saddle addresses the issue of difficult string changes. Instead of frustration resulting from trying to feed an uncooperative string through numerous minuscule holes, the guitar player would simply have to push the string half an inch into the saddle, and it would be secure. Removing the string is even easier, requiring only a button press. Since the string is secured very well by the clamps, tuning stability would also improve. The saddles themselves will be made to retrofit into standard bridge designs, replacing the standard saddle. The "raccoon trap" saddles would be twice as expensive to manufacture as current saddles, but since standard saddles cost so little, this cost would not be particularly significant. The saddle would be made out of cast and stamped steel, and would only have a few parts, making it easy to manufacture and assemble.

Comparison of Designs
Description Fender Bridge Floyd Rose Linear Bridge Digital Bridge Cartridge Bridge "Raccoon Trap" Bridge
Sketch
Criteria Weight Datum 1 Datum 2 Design 1 Design 2 Design 3 Design 4
Manufacture/Assembly 1 0 - - + + -
Affordable 1 0 - - - 0 -
Tuning Stability 3 0 + ++ +++ + +
String Change Difficulty 3 0 + + + ++ ++
Installation Difficulty 1 0 - + - 0 0
Easy to Use 2 0 - + + + +
+ 0 6 13 15 12 11
0 9 0 0 0 3 1
- 0 5 2 1 0 2
Net Score 0 1 11 14 12 9
Conclusion

When we compared the four designs using a Pugh chart, we found that the winner was the cartridge bridge. The main deciding factor was the cost of the bridge, which has a major influence on the market share of the bridge. Besides its low cost, the cartridge bridge has excellent tuning stability, and easy to change strings.

Depending on the manufacturing and marketing capabilities of our client, we would not hesitate to recommend any of our design concepts. However, given the specific instructions given to us by Initech, we felt that the best design is the cartridge bridge. The cartridges combine major improvements with more modest changes to the overall design of the guitar, which will make it easier for Initech to manufacture and sell new guitar bridges. A cartridge design will also create a new market for guitar string cartridges, which Initech can capitalize on.

Store Research

We conducted an interview with a store clerk at [Daddy's Junky Music], in Burlington Massachusetts. The store clerk told us that 50% of electric guitars sold at the store had a Fender bridge installed. 10% had a Floyd Rose bridge, and the remaining 40% had fixed bridges, or less well known tremolo designs, like the Bigsby and Kahler tremolos. These numbers were in line with our assumption that the Fender bridge caters to the larger amateur guitarist market, while the Floyd Rose dominates the high end market.

We were unable to find national or worldwide numbers on guitar sales. None of the major guitar companies make their sales information publicly available.

Final User Feedback

Our booth at the Design Exposition
Our booth at the Design Exposition

Once we had a working Prototype 3 bridge installed in a playable guitar, we began user testing it with local guitarists. All were impressed and enthusiastic about the improvements that our design implements. Two distinct issues arose that our users were concerned with. The first was our use of non-standard strings. Users were concerned less with cost than with availability – concerns of not being able to find strings locally for such a specialty item. We agree with this concern and are planning a conversion saddle for standard strings similar to the ones used in our prototypes. We would package six spare saddles with the bridge so the user could have a full set of saddles pre strung and ready to use.

The second issue that our users identified was our design's lack of a variable action. The action is a series of screws that can be altered to adjust the height and position of each saddle individually. Our model sacrifices this variability for better tuning stability and much lower production costs. None of the users we surveyed used this feature often, and most were satisfied with the preset positions that our bridge uses.

On positive features, our testers were very happy with the easy string changing capabilities of our bridge. Users who played our prototype were surprised with how well our model held it's tuning while playing, something they were not used to. One working musician even offered to buy our prototype guitar. Our testing gives us confidence that our design would be able to compete directly with low cost models currently on the market due to our simple design and high quality performance.

Prototype Design

Prototype 1

Prototype 1 was a proof of concept that our rail design bridge would work. It consists of a single saddle, and a small base plate. The base plate is constructed of two pieces of aluminum screwed together. The rails are glued in. We learned that the design was indeed feasible, and that the cartridge would not have tolerance issues with the manufacturing processes available to us. It was constructed in approximately 4 hours by Jeremy and Aaron.

Pictures

Figure 1:  Close up of Prototype 1 Bridge (Click to Enlarge)
Figure 1: Close up of Prototype 1 Bridge (Click to Enlarge)
Figure 2:  Original Sketch of Rail Design Bridge (Click to Enlarge)
Figure 2: Original Sketch of Rail Design Bridge (Click to Enlarge)

Prototype 2

Changes from Prototype 1

Prototype 2 was the first fully functional prototype. It consisted of a scaled up version of Prototype 1, with a few changes.

The Prototype 2 saddles were slightly shorter, will the string hole closer to the bridge. This put the strings at the same height as a Fender bridge. The Prototype 2 saddles also had a shelf cut out of them. This put the exit point of the string at the correct location for the scale of the guitar. The base plate is constructed out of two pieces of aluminum, a plate and the rail holder, which were screwed together. The rails were glued in place. The prototype was designed to reuse the screws, sustain block, and whammy bar from the Fender Bridge.

Prototype 2 was designed in Solidworks 2007 by Mike and Jeremy, and was constructed in the Machine Shop by Aaron, Mike, and Jeremy, and took approximately 25 man hours of work to build.


Pictures

Figure 3:  Prototype 2 Parts (Click to Enlarge)
Figure 3: Prototype 2 Parts (Click to Enlarge)
Figure 4:  Prototype 2 Assembled and Installed (Click to Enlarge)
Figure 4: Prototype 2 Assembled and Installed (Click to Enlarge)
Figure 5:  Prototype 2 CAD Rendering (Click to Enlarge)
Figure 5: Prototype 2 CAD Rendering (Click to Enlarge)

Prototype 3

Changes from Prototype 2

In terms of design, Prototype 3 was a minor departure from Prototype 3. It consisted mainly of small changes to optimize manufacturing and tuning stability. The base plate was condensed into one piece of aluminum instead of two, for ease of manufacturing, and eliminating three screws. Several of the screw holes were moved slightly. The saddle bar was designed to allow for correct intonation (small changes in the length of the strings to account for the different string thicknesses). It was also corrected for the string radius (strings are not all flat on the guitar, but curved around an imaginary radius for playing comfort). These changes made the design very complicated to machine, so it was done on the CNC Mill in the machine shop.

The saddles, sustain block, whammy bar, and screws were reused from Prototype 2. The rods were shortened from 1 inch to 0.75 inches.

Prototype 3 was designed by Jeremy in Solidworks 2007. The baseplate was manufactured on the CNC machine. The remaining parts were taken from Prototype 2, or manufactured in the machine shop by Aaron, Mike, and Jeremy. It took approximately 9 man hours to tweak and install Prototype 3. This figure does not count the CNC time for manufacturing the base plate.

Prototype 3 is very similar to our final design, with the exception of manufacturing methods. Prototype 3 was machined on a CNC and milled by hand. Most of the parts for the final design will be cast.

CAD

Full CAD Models for Prototype 3 are available here.

Pictures

Figure 6:  Prototype 3 CAD Rendering (Click to Enlarge)
Figure 6: Prototype 3 CAD Rendering (Click to Enlarge)
Figure 7:  Prototype 3 in Guitar CAD Rendering (Click to Enlarge)
Figure 7: Prototype 3 in Guitar CAD Rendering (Click to Enlarge)
Figure 8:  Prototype 3 Installed in Test Guitar (Click to Enlarge)
Figure 8: Prototype 3 Installed in Test Guitar (Click to Enlarge)
Figure 9:  Prototype 3 Base Plate (Click to Enlarge)
Figure 9: Prototype 3 Base Plate (Click to Enlarge)

Mechanical Analysis

Summary and Introduction

When designing our bridge, we decided to focus on creating an easy to use, affordable bridge, with superior ability to hold tune. Tuning is a major problem for current bridge designs, especially the Fender design. This issue is of great important to guitarist of all skill levels.

We first considered how the Fender Bridge works, to find problem features that allow the guitar to go out of tune. We then looked at our prototype design for similar problems. Using MATLAB, we calculated how these factors would effect the tuning. We then performed experiments on actual guitar bridges to determine their real world performance.

We also considered how the tremolo effects the frequency of vibration of the strings, which gave us insight into how a guitar bridge works.

Tuning Stability

Figure 1:  Close up of Fender Bridge
Figure 1: Close up of Fender Bridge

In this design memo, we chose to examine the effect of the design flaws of the Fender bridge on the tuning of a guitar string. We then compared these effects to the simulated behavior of our Prototype 2 design. We found that the Fender Bridge offers very poor tuning stability, while our Prototype 2 design exhibits excellent tuning stability.

Saddle Slippage

One major design flaw in the Fender bridge is that each string saddle is anchored only by a long screw, and the friction between the base-plate and saddle caused by string tension pushing the saddle down. This allows the saddle a great deal of freedom of movement and rotation, especially when the string is slack. On a guitar with no tremolo, this would not be a problem. However, on a guitar with a tremolo bridge, the strings can easily become slack if the user pushes the tremolo by an appreciable amount (by our first quantitative analysis, the G string will be completely slack at a 6.1 degree tremolo angle, and all strings except the high E string are flat by 10 degrees). The saddle is able to translate horizontally, describing an arc with the center at the point where the screw meets the bridge. The saddle can move forward and backwards, since the screw hole is not threaded on the bridge. Finally, the saddle can rotate around the screw. Of these movements, the most likely, is the horizontal translation. We simulated this phenomena using MATLAB.

Figure 2:  Degrees of Freedom of Saddle on Fender Bridge
Figure 2: Degrees of Freedom of Saddle on Fender Bridge

The guitar can be simply modeled as follows:

Figure 3:  Model of Guitar Bridge for Saddle Slippage
Figure 3: Model of Guitar Bridge for Saddle Slippage


The angle Θ is the angle of the saddle with respect to its angle when it is correctly lined up. Theta will in general be very small, and difficult to measure. For this reason, we also define M as M= L_saddle sin(θ) . M is the horizontal translation of the saddle. This is easier to measure on a real guitar. Lsaddle is equal to 1”, so M is very small. For the purposes of our test, we chose to examine M in the range of 0 to 2mm, which corresponds to a range of Θ equal to 0 to 3 degrees. The 25.5” measurement is the length of the strings when they are in the neutral, correct position. The Lstring variable represents the length of the strings when the saddle is in the incorrect position. The relation between Lstring and M, or Θ is a simple matter of geometry.

Image:guitar_ma_eqn1.png

The string can be modeled as a spring. The two ends of the string are fixed, so any change in length of the string while the guitar is being played means that the tension is also going up. In order to stretch the string from 25.5” to Lstring, the string tension goes up by:

Image:guitar_ma_eqn2.png

Figure 4:  Tuning error from Saddle Slippage
Figure 4: Tuning error from Saddle Slippage

Where T0 is the original, in-tune tension of the string. The frequency of a vibrating string is dependent on the tension, length, and linear mass of the string. All of these are known. For reference for the numbers we used, please see our first design report’s quantitative analysis. The strings are standard “light” guitar strings, which are the most common electric guitar strings sold.

Image:guitar_ma_eqn3.png

Armed with these equations, we found the frequency change for each string. In order to display the data in a more intuitive format, we graphed the tune of the strings in units of cents. Cents are a logarithmic scale, with 100 cents between each musical note in the scale, or 1200 cents in an octave. A note that is 100 cents out of tune is has moved one piano key from its original tune. The average layman can hear a musical note that is 25 cents or more out of tune. A musician can hear a wrong tuning in the range of 5-6 cents.


The saddle slippage causes a relatively large amount of error that would be obvious even to untrained musicians.

Ball End Rotation

Figure 5: The String Stretches when Twisted (Top) Ball Ends are Visible with Different Rotations (Bottom)
Figure 5: The String Stretches when Twisted (Top) Ball Ends are Visible with Different Rotations (Bottom)

We also considered the tuning error caused by the ball end of the string rotating. In the Fender bridge, the ball end is held secure only by string tension. When the tremolo is used, and the strings are slack, the ball ends can rotate before being pulled taunt again. This rotation adds twist to the strings, which causes it to take a very slight helix shape. We approximated this by saying that the string takes on a helical shape with a diameter the same as the string diameter, and the number of turns equal to φ/360, where φ is the angle of rotation of the ball end. This change in length again changes stretches the string, changing the tension. However, the vibrating length of the string remains the same. In the case of ball end rotation, the string length changes, but the length between the nut and saddle does not change. This means, in effect, that the string stays the same length, while the tension gets higher. Using our frequency equations from above, we graphed the change in pitch from a rotated ball end.

Image:guitar_ma_eqn4.png

Figure 6: Ball End Rotation Compared to Tuning
Figure 6: Ball End Rotation Compared to Tuning

The results of the graph were surprising. The strings very quickly went out of tune, even for a very small rotation of the ball end. The red dotted lines represent how musical notes out of tune the guitar is. For instance, at 70 degrees of rotation, the G string has gone from a G note (196.00 Hz) to a Bb (233.08 Hz). A rotation of 25 or 30 degrees would not be at all unusual, and an enthusiastic guitarist might easily have the ball ends rotate more than that.

Prototype 2

Our Prototype 2 Bridge design has neither of the previously addressed tuning issues. The string does not have a ball end, and is secured by epoxy inside the saddle cartridge. The saddle cartridge is secured to the bridge plate by two strong “rails” instead of one flimsy screw. Since the sliding fit we used on our saddles has a gap of only 3 thousands of an inch, the saddle can rotate very little, orders of magnitudes less than the Fender bridge. We used MATLAB to see how the little freedom of movement left to the saddle would affect the tune.

Image:guitar_ma_eqn5.png


Figure 7:  The Prototype 2 Saddle in the Correct Position (left), and at the Worst Case Rotation (right)
Figure 7: The Prototype 2 Saddle in the Correct Position (left), and at the Worst Case Rotation (right)

Where Wsaddle is the width of the saddle (0.4 inches), Tsaddle is the tolerance of the hole in the saddle (0.003 inches), and Lsaddle is the length of the saddle (0.5 inches). According to MATLAB, our maximum change in string length is 0.0012 inches, or 0.0305 mm. We plugged this into our frequency equations.

Figure 8:  The Worst Case Scneario of the Tuning of the Prototype 2 Design
Figure 8: The Worst Case Scneario of the Tuning of the Prototype 2 Design

We only evaluated the Prototype 2 design at two angles, the “correct” neutral angle, and at the worst case scenario. It is unrealistic that the bridge would be at any angle besides these two, because the design is not held in place by friction, like on the Fender Bridge, but by normal forces from the rails and the front bridge stop. We can immediately see that our bridge design has excellent tuning stability. At the worst case, the G string is about 4 cents out of tune, which is inaudible even to a trained musician. This is 10x lower than even a well behaved Fender bridge. It is worth noting that the Floyd Rose bridge offers similar tuning stability to our own bridge. However, the Floyd Rose bridge caters to the upscale guitar market, while we intend our bridge for the lower end market, where the Fender Bridge is prevalent.

Experimental Data

Figure 9:  Graphs of Tuning Stability (Click to Enlarge)
Figure 9: Graphs of Tuning Stability (Click to Enlarge)

In order to test our mathematical model, we created a standardized experiment, and ran it for several different types of guitar bridges. The experiment was conducted as follows:

Procedure

1) The guitar was put into exact tune using an electronic tuner. Standard EADGBe tuning was used with A = 440 Hz.

2) The whammy bar was depressed on the guitar as far down as it would go, then released.

3) The tuning of each string was recorded using an electronic guitar tuner.

4) This process was repeated five times.

5) Results were plotted using Microsoft Excel, with units of cents*.

* Cents are logarithmic units of tuning. There are 100 cents between adjacent musical notes (i.e. B and Bb). This means that a string that is 100 cents out of tune is one semitone flat or sharp. An untrained human ear can detect a tuning error of 25 cents, while a trained musician can detect an error of 4 cents).

This experiment simulates how the guitar will go out of tune as the whammy bar is used while playing. This is very important to guitarists, who need a guitar to stay in tune for a whole song, and prefer guitars that can stay in tune for many songs in a row.

We tested several different guitar bridge designs:

1) Fender Tremolo without Locking Nut 2) Fender Tremolo with Locking Nut 3) Bigsby with Locking Tuners 4) Floyd Rose with Locking Nut 5) Prototype 2 Bridge

After testing a Fender guitar without a locking nut, we decided this could be a source of error, installed one, and tested again. The nut is the small piece of plastic at the top of the guitar nut that holds the strings off the fretboard. The strings can get caught on the nut, which can affect the tuning of the guitar. Since we were not considering the nut for our design improvements, we installed a locking nut on the guitar to eliminate error. A locking nut incorporates a clamp onto the nut, so the string is not able to slip. Locking nuts are available for $10 and are easy to install. The Floyd Rose bridge system comes with a locking nut as standard.

Results

We found that the Fender bridge was by far the worst design for tuning stability, with or without the locking nut. Without the locking nut, the Fender strings detuned by 40 to 60 cents over the course of the experiment. The result of this would be a guitar that would be painful to listen to.

With the locking nut, the Fender bridge had tuning errors between 20 and 40 cents. Again, this would be easily (and unpleasantly) audible to a non-musical listener. The tuning errors we found for the Fender bridges are in line with our mathematical predictions for Saddle slippage, which predicted a maximum of 40 cents tuning error. The Fender bridge without a locking nut also exhibited an interesting behavior on the low E string, which immediately shot to 60 cents error. This is either due to ball end rotation (which predicts anywhere from 0 to 400 cents tuning error), or to the string slipping on the nut.

The Bigsby Bridge is another tremolo from the 1950s. It was more expensive and less popular than the ubiquitous Fender model. The reason for its extra cost became evident when we tested it. The tuning error remained below 20 cents for most of the strings, with the D string barely touching 25 cents of error at the end of the test. This would result in a guitar that remains in tune well enough to finish at least one song, while still sounding harmonious.

The Floyd Rose bridge also had excellent results. Over the course of five tests, the strings rarely strayed above 20 cents error, with a maximum error of about 30 cents for the G string. This means that the Floyd Rose would also be useful for guitarists who use the tremolo bar a lot, and want their guitar to stay in tune. It should be noted that the Floyd Rose equipped guitar we tested had very old strings, while the rest of the guitars had fresh strings. Old strings maintain tune poorly compared to newer strings, so this probably increased the tuning error of the Floyd Rose, which we expected to have even less tuning problems than the Bigsby.

Finally, our Prototype 2 bridge had phenominal results. Not only did it have very little tuning error (a maximum of about 15 cents), but it had excellent stability, indicating that the tuning error was likely to stay in the 15 cent range even if the tremolo was used many more times. Our mathematical predictions said that the tuning error for our bridge should be in the 0-4 cent grange. Our actual results are a bit higher. This is not surprising, since the tolerances on our prototype were much worse than those we assumed for a production model.

Error

There are a number of sources of error in our experiment. We assumed that the only cause of tuning instability comes from the bridge. This not the case. In guitars without locking nuts, much of the tuning instability comes from the nut and tuners. Since all of our guitars but one had locking nuts, this source of error is probably not important. Another source of error is the bending of the neck. The guitar neck is often assumed to be completely rigid, but in fact bends considerably while the strings are under tension. This bending is not always perfectly elastic, and can effect the tuning. The strings are modeled as ideal springs in our math, but of course real strings are not perfectly elastic. They undergo plastic as well as elastic deformation, and have inherent damping. This can also cause tuning changes. The electronic tuner is supposed to have an accuracy of +/- 1.5 cents. The display on the tuner is accurate to 2 cents. These also caused a lack of measuring precision.

Overall, we feel that the sources of the error are probably not a problem in our results. We feel that the error probably accounts for less than +/- 10 cents, which would only seriously affect the results on the Prototype 2 bridge. Our results are still in line with what our math predicted.

Musicality

In our first design report, we also extensively examined the proportional tuning of guitar strings as the whammy bar is depressed. This analysis was used as a tool to consider how to create a more musical whammy bar. This design feature was eventually abandoned when we decided to focus on building a low cost, highly tuning stable bridge. However, this analysis offers some interesting insight into how a guitar bridge changes the tune of a guitar. It can be accessed here:

Quantitative Analysis of the Musicality of an Electric Guitar Tremolo

Our design functions similarly to the Fender or Floyd Rose with respect to musicality, so the analysis is valid for our bridge.

Conclusions

From our mathematical analysis, our prototype design clearly offers better tuning stability than the Fender bridge. It does this by reducing the number of degrees of freedom allowed to the parts of the bridge, and tightening the tolerances on these degrees of freedom. Our manufacturing analysis will explain that we are able to do this without raising the cost much above that of a standard Fender bridge. The Floyd Rose bridge offers many of the tuning advantages of our design, but in a more complicated, expensive, and less user friendly package.

Our experimental analysis clearly shows that even in prototype form, the tuning advantages to our bridge are obvious. These advantages translate into the guitarist not needing to tune his guitar as often, which was our goal. The stability of the bridge also encourages the guitarist to use the tremolo more often, since he will not be afraid the guitar will go out of tune.

Our bridge design does not increase the musicality of the tremolo effect when compared to the Fender Bridge. On the other hand, all currently available bridges have the same problem, so it is not a disadvantage. However, it is certainly an area that merits further research. Our cartridge idea could easily be applied to a bridge that does improve upon musicality.

Manufacturing

FMEA

Failure Mode and Effects Analysis (FMEA) is a crucial tool in determining if a particular component in a system will fail (in terms of the customer's requirements). By looking at each piece, we can rate the severity of a failure (S), the probability that it will occur (P), and the likelihood that the customer would detect the failure (D). The severity of failure is rated between 1-10, 1 being the effect is not noticed by the consumer, while 10 is hazardous. Probability of occurence is also rated from 1-10, 1 being extremely remote while 10 has an extremely high chance of occurring. Finally, detection is rated from 1-10 with 1 being almost certain to detect and 10 being no chance of detection whatsoever. With these three factors, we can multiply them together to achieve a total risk priority number (RPN) which can range from 1-1000 (1000 being the greatest risk). Below is a table outlining each part.

Previous Design Failure Mode Analysis

To determine areas of weakness in currently existing designs, we ran failure mode analysis on both the Fender and Floyd Rose Bridges. This analysis is available at the Guitar Bridge FMEA page.

Prototype Failure Mode Analysis

Item & Function Failure Mode Effects of Failure S Causes of Failure P Design Controls D RPN Recommended Actions
P3 Cartridge/Saddles
  • Secure strings to bridge
  • Prevent unwanted string movement
String breaks either inside cartridge or outside Cannot play guitar without strings 6 Fatigue due to playing strings 8 Outside analysis of project 1 48 Use higher grade strings
P4 Rods
  • Secure cartridges to bridge
  • Prevents movement of saddles
Bent Rods Cannot fit cartridges/saddles onto bridge 7 Dropped guitar 2 Drop Guitar (bridge facing down) 3 42 Switch rods to steel instead of aluminum
Saddle slid on roughly or improperly 1 Apply varying lateral forces to saddles 3 21
  • Create user manual explaining proper way to change saddles
  • Chamfer ends of rods or saddles to ease insertion
P5 Whammy Bar
  • Allows user to control tremolo function
Shear failure at base Broken handle, leading to an inability to use tremolo function without replacement. 5 Bar not strong enough near base 2 Test for imperfections using x-ray 5 50 Design bar to be thicker at base, where forces are greatest
Hard to tell if bar is inserted correctly 1 None (design flaw) 1 5
  • Design bar so it is easier to insert fully (like the Floyd Rose)
  • Add colored section to the end of the bar, if colored section is showing, bar is not inserted fully
P8 Springs
  • Provides counter force to string tension
  • Returns bridge to tune after use of tremolo function
When springs removed for servicing, may shoot off Harm to guitar, or user 9 Springs not adequately anchored 3 Measure spring tension at factory 3 81 Design springs to be easily removable, or create anchor cable to prevent spring from flying away (like a garage door spring cable)

Conclusions

The two main categories our failures fall into are user error and material fatigue. User errors can be greatly reduced by changing aspects of the design, to make it more intuitive to use. A balance must be struck between adding "easy to use" features to the bridge, and the cost and complexity of the bridge. Material fatigue is unavoidable, especially in standardized parts like the screws, strings, and springs. The best course of action in situations where these are an issue is to find suppliers of higher quality parts.

Since the design of the cartridge bridge is very similar to that of the Fender bridge, many of the same weaknesses are evident, especially for the parts that we took directly from the Fender bridge (i.e. the whammy bar or the springs). New areas of weakness includes the cartridge rails.

The one failure point that stands out on both bridges and the prototype is the possibility of the springs flying off the guitar when the user tries to remove them. These springs have the potential to cause a good deal of damage, both to the guitar (scratched paint), and to the user (spring in the eye). This failure point is also one of the easiest problems to fix. It would be easy to implement a safety cable similar to those used in garage door springs, to catch the spring when it is released from its mounting points.


Overall, guitar bridges are not considered dangerous devices. Catastrophic failure is uncommon, and in general, inconvenient instead of dangerous. The only area that may warrant further resources is the spring system. Redesigning the spring retention mechanisms could be a simple and effect method of correcting this. However, this would be abandoning certain standardized parts for the bridge, which would increase the cost.

DFMA

Design for Manufacture (DFM)

Prototype 2 Parts (Click to Enlarge)
Prototype 2 Parts (Click to Enlarge)

DFM allows for the design of products while reducing manufacturing cost and ameliorating product quality. Through the process of product dissection, it became apparent the different components of the system, the materials that were utilized, and the manufacturing process used for fabrication.

The Fender bridge that came with the guitar contained 6 unique parts (not including the guitar assembly itself). Leo Fender, designer of the Fender bridge, as well as many other guitar related technologies, designed his bridge to be easy and cheap to manufacture, by using few parts in easy to manufacture shapes. In contrast, the Floyd Rose bridge contains six more parts (12 in total). The number of parts in any design should be minimized as much as possible without adding too much complexity to the remaining pieces. The reasoning behind this is that it is a great savings and it makes the overall design simpler in most cases. In the case of the Floyd Rose bridge, the extra parts are necessary for increased functionality. In a good design, functionality and simplicity of manufacture have to balance each other out.

In both designs, about a third of the unique components were standard screws. In terms of total parts count, screws accounted for 2/3 to 3/4 of the total number of parts. The standardization of parts helps bring manufacturing costs down, but it makes the assembly more difficult.

Our bridge design has only three unique parts (the base plate, the sustain block, and the rods). The base plate and sustain block can be cast, and the rods can be extruded. All parts are made out of aluminum. The sustain block and base plate require several precision holes be drilled after casting, but this would not be difficult with a CNC machine. There are a total of 22 holes in the base plate, but only 12 of these need to be drilled with the CNC for close tolerance requirements, the remainder can be included in the casting mold. The sustain block has 10 holes, but only 4 of these need to be drilled and tapped precisely, the rest can be tapped. The rods, made out of standard 1/8" aluminum bar stock, can be cut using a band saw or cutting press. Aluminum welding rod has a tolerance of 1/1000" of an inch, which is acceptable for our press fitting.

We also use several externally supplied parts in our design. This reduces manufacturing costs. Our tremolo bar and springs are both purchased from vendors. These parts are made out of steel. Our fasteners are standardized steel screws, and are purchased from external suppliers.

Our bridge, if produced in equal quantities to the Fender bridge, would cost much less to produce. Even in relatively low quantities, this means we can be price competitive in the low end guitar bridge market.

Design for Assembly (DFA)

DFA has very similar restrictions as that of DFM. Generally, you want to minimize as many parts as possible. In some respect, this is a major flaw in both bridge designs so far. The number of screws and fasteners used greatly reduces the assembly time of these products. Given the amount of parts used, it is fair to assume that these bridges are assembled either via manual assembly or automatic assembly, but not by robotic assembly.

Assembly requires human labor because of the number of dexterous operations required, but because the labor is not particularly skilled, these bridges are probably assembled either in China, in large quantities, or at the guitar factory, as needed.

Assembly of a Fender Bridge probably takes less than a minute for a practiced worker with a powered screw driver. The Floyd Rose bridge probably requires 2-3 minutes of assembly time, as it has many more parts, which must be assembled in a specific order. Our final bridge design contains only three fasteners. This is a major reduction from the 9 required for the assembly of the Fender, and the 20+ screws in the Floyd Rose. The only two steps in assembling our bridge are the attachment of the sustain block to the base plate by three screws, then the press fitting of the rods to the base plate. These rods can all be attached at once using a simple jig. This means it would be easy for one or two workers to assemble a hundred bridges an hour with only minimal tools. The assembled bridges are just as easy to install in a guitar as a Fender bridge (which it is mount compatible with). Six screws anchor the bridge, and three springs are installed on the back. The user installs the cartridge strings on the bridge.

DFE

Design for Environment (DFE) is a very important component of the entire design process given the current state of affairs in the world today. We are experiencing a dramatic increase in carbon dioxide production, leading to global warming which effects ecosystems in potentially catastrophic ways. Engineers need to be able to quantify the impact their products have on the world and on the environment. In order to do this efficiently, a tool is utilized called Economic Input-Output Life Cycle Assessment (EIOLCA) which is a quick and easy alternative to the more traditional Process-based Life Cycle Assessment. This tool allows engineers the ability to investigate, estimate, and evaluate the environmental burdens caused by a material, product, process, or service throughout its life span. Since a guitar bridge, once assembled, is not very detrimental to the environment, this analysis will focus on the production and transportation of the product.

Economic Activity

An injection of $1 Million Dollars into this sector creates a net influx of $2.07 Million in all sectors. This is distributed among many different sectors ranging from transportation to trade.

Image:economic.jpg

Air Pollutants

For every $1 Million Dollars spent in this sector, 12.159 Tonnes of air pollutants are produced, mostly coming from the power generation and supply of the manufacturing process. Air pollutants are detrimental to one's health and can ruin certain ecosystems. The most abundantly produced air pollutant in our analysis is carbon monoxide. CO effects the air quality in the atmosphere and exposure to it can produce a spectrum of negative health effects such as shortness of breath and dizziness.

Image:air_pollutants.jpg

Greenhouse Gases

468 MTCO2E (Metric Ton CO2 Equivalent) are produced mainly from the power generation sector. It are these gases that contribute to the warming of the Earth due to the Greenhouse Effect.

Image:greenhouse.jpg

Toxic Releases

Image:toxic.jpg

Conclusions

A guitar bridge requires no lubrication or maintenance, nor does it require fuel. The lifetime of a guitar bridge is the lifetime of the guitar. The first electric guitars built in the 1950's are still going strong, so there is no reason to assume that modern, more refined guitars shouldn't last centuries, if the most basic care is taken with them. Guitars, and most other musical instruments, are part of a thriving used market. Guitars that are bought are rarely discarded, but instead sold to other musicians, minimizing the amount of recycling going on. Because of these factors, the environmental impact of a guitar bridge can be assumed to be almost identical to the environmental impact of its manufacture.

For our EIO-LCA, we chose to model our guitar bridge as "musical instrument manufacturing". We believe this is accurate because the bridge is a musical instrument piece, and the companies that manufacture them have their own factories, instead of using contracted factories in the general metal production sector. The bridge is not a typical musical instrument, as it is made entirely of metal, instead of wood, plastic, and metal. However, we believe that the musical instrument sector is still the best match.

Our results show that the majority of the pollution emitted during the production of our product is from power generation. This makes sense, since metal casting requires large amounts of power to heat the metal to melting point, and for the industrial equipment to handle the molds. A significant amount of pollution is generated during musical instrument manufacture. This comes from things like toxic paint fumes, and processes that use hazardous chemicals like electroplating.

Guitar bridges are easy to recycle. The parts are all easy to disassemble (screws only), and all parts are made of relatively pure (if not high grade) metals, including steel and brass. Easy disassembly and high amounts of metal make guitar bridges very low cost and high return to recycle, providing users with incentive to recycle bridges. We do not see recycling as being a major issue, especially when considering the fact that very few guitars actually get scrapped. Our design improves upon previous designs, because we use easy to recycle aluminum. If the guitar ever does get scrapped, the aluminum parts are easy to remove, and use elsewhere. It would even be possible to use low grade recycled aluminum for the sustain block, to further offset our environmental impact.

The fact that pollution is released during manufacture is unavoidable. When we considered the amount of pollution released per bridge, we found that guitar bridges are actually quite eco-friendly. If a $50 per metric ton of CO2 equivalent pollution tax were implemented, each bridge would be taxed at $0.47. This product is meant to last a lifetime, so if we consider the environmental impact spread over 20 years, then the tax would be less than $0.03 per year.

Design Process

General Overview

Our team worked relatively democratically. The team leader's responsibility was to schedule meetings and create schedules for the completion of various aspects of the project. Jeremy was the team leader for reports 1 and 2, and Mike was the team leader for the final report. In general, team members specialized in one area of the design, and wrote the corresponding section for each report. Jeremy concentrated on the quantitative analysis. Mike specialized in the user research. Aaron specialized in market and patent research, and Jonathan specialized in manufacturing analysis. Specialization allowed continuity between each report, as team members could build on their own previous efforts for each new report. Team members were kept updated on each others progress by frequent team meetings.

Next Steps

At this point, we have the designs for a demonstrable prototype. As discussed in the market research, in the current competitive guitar market, in order for a new bridge design to succeed, it needs the sponsorship of a major manufacturer. The next step for our team would be to take out a provisional patent, and to begin to demonstrate the design for various guitar companies.

Team Member Contributions

Image:guitar_aaron.jpg Image:guitar_jeremy.jpg
Mike Harrison Aaron Marks Jonathan Kyle Jeremy Ozer

Aaron

  • Shop work on prototypes 1, 2, and 3.
  • Patent Research on Report 1.
  • Market Research on Report 3.
  • Quality Function Deployment (QFD) on Reports 1, 2, and 3.

Jeremy

  • Shop work on prototypes 1, 2, and 3.
  • Solidworks design on prototypes 2 and 3.
  • Team Organizer on Reports 1 and 2
  • Quantitative Analysis on Report 1, Design Memo, and Final Report
  • Report Editor on Report 1 and the Final Report
  • Guitar Experimentation
  • User Research
  • Photography
  • CAD Renderings
  • Accounting, Purchasing, and Budgeting

Jonathan

  • Product Design Analyst
  • DFMA, DFE, FMEA
  • Gannt Chart
  • User Surveys
  • Report 2 Editor

Mike

  • Shop work on prototypes 2 and 3
  • Solidworks design for prototypes and final design
  • Team organizer for final report and presentation
  • Market research user studies
  • Executive summaries

Gantt Chart

Gantt Chart of our Project Progress(right)
Gantt Chart of our Project Progress(right)

Appendix A: MATLAB Code for Mechanical Analysis

Whammy Bar Musicality Analysis MATLAB Code is available here.

Tuning Comparison MATLAB Code is available here.

Appendix B: Reference Patents

Floyd Rose Bridge[2]
Fender Bridge[3]
Tremolex[4]
Fastening Means for Guitar Strings[5]
Cartridge String Guitar Assembly[6]

Appendix C: References

"Callaham Tremolo Blocks." Callaham Guitars. 1 Oct. 2008. Callaham Guitars. 6 Oct. 2008 <http://www.callahamguitars.com/blocks.htm>.

"Floyd Rose Tremolo." A Amps Electric Guitar Store. A Amps Electric Guitar Store. 6 Oct. 2008 <http://aampselectricguitarstore.com/floyd-rose-locking-tremolo/>.

GanttProject. 6 Oct. 2008 <http://ganttproject.biz/index.php>.

Personal tools