Mop wringer
From DDL Wiki
(→Bill of Materials) |
(→Bill of Materials) |
||
Line 129: | Line 129: | ||
| Extruded, cut, bent | | Extruded, cut, bent | ||
| 219 | | 219 | ||
- | |[[Image:Bucket_Handle.jpg]] | + | |[[Image:Bucket_Handle.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 147: | Line 147: | ||
| Injection Molded | | Injection Molded | ||
| 781 | | 781 | ||
- | | [[Image:Upper_Wringer_Plate.jpg]] | + | | [[Image:Upper_Wringer_Plate.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 156: | Line 156: | ||
| Injection Molded | | Injection Molded | ||
| 1520 | | 1520 | ||
- | | [[Image:Bottom_Wringer_Plate.jpg]] | + | | [[Image:Bottom_Wringer_Plate.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 165: | Line 165: | ||
| Extruded, cut | | Extruded, cut | ||
| 48 | | 48 | ||
- | | [[Image:Linkage_Stabilizing_Pin.jpg]] | + | | [[Image:Linkage_Stabilizing_Pin.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 174: | Line 174: | ||
| Stamped | | Stamped | ||
| 69 | | 69 | ||
- | | [[Image:_Upper_Wringer_Plate_Linkages.jpg]] | + | | [[Image:_Upper_Wringer_Plate_Linkages.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 183: | Line 183: | ||
| Purchased | | Purchased | ||
| 4 | | 4 | ||
- | | [[Image:Rivets.jpg]] | + | | [[Image:Rivets.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 192: | Line 192: | ||
| Extruded, cut, bent (purchased) | | Extruded, cut, bent (purchased) | ||
| 937 | | 937 | ||
- | | [[Image:Wringer Lever.jpg]] | + | | [[Image:Wringer Lever.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 201: | Line 201: | ||
| Extruded, bent (purchased) | | Extruded, bent (purchased) | ||
| 4.4 | | 4.4 | ||
- | | [[Image:Lever_Torsional_Spring.jpg]] | + | | [[Image:Lever_Torsional_Spring.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 219: | Line 219: | ||
| Purchased | | Purchased | ||
| 18 | | 18 | ||
- | | [[Image:Wheel_Bolt.jpg]] | + | | [[Image:Wheel_Bolt.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 228: | Line 228: | ||
| Purchased | | Purchased | ||
| 4 | | 4 | ||
- | | [[Image:Wheel_Nut.jpg]] | + | | [[Image:Wheel_Nut.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 237: | Line 237: | ||
| Injection Molded | | Injection Molded | ||
| 67 | | 67 | ||
- | | [[Image:Wheel_Mount.jpg]] | + | | [[Image:Wheel_Mount.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 246: | Line 246: | ||
| Purchased | | Purchased | ||
| 21 | | 21 | ||
- | | [[Image:Wheel_Mount_Pin.jpg]] | + | | [[Image:Wheel_Mount_Pin.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 273: | Line 273: | ||
| Purchased, cut | | Purchased, cut | ||
| 50 | | 50 | ||
- | | [[Image:Folding_Mop.jpg]] | + | | [[Image:Folding_Mop.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 282: | Line 282: | ||
| Purchased, cut | | Purchased, cut | ||
| <1 | | <1 | ||
- | | [[Image:Scrubbing_Pad.jpg]] | + | | [[Image:Scrubbing_Pad.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 291: | Line 291: | ||
| Extruded, cut, bent (purchased) | | Extruded, cut, bent (purchased) | ||
| 4 | | 4 | ||
- | | [[Image:Folding_Plates_Spring.jpg]] | + | | [[Image:Folding_Plates_Spring.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 300: | Line 300: | ||
| Injection Molded | | Injection Molded | ||
| 23 | | 23 | ||
- | | [[Image:Folding_Sponge_Plate.jpg]] | + | | [[Image:Folding_Sponge_Plate.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 309: | Line 309: | ||
| Injection Molded | | Injection Molded | ||
| 18 | | 18 | ||
- | | [[Image:Mop_End_Cover.jpg]] | + | | [[Image:Mop_End_Cover.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 318: | Line 318: | ||
| Injection Molded | | Injection Molded | ||
| 38 | | 38 | ||
- | | [[Image:Plate_Folding_Handle.jpg]] | + | | [[Image:Plate_Folding_Handle.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 327: | Line 327: | ||
| Injection Molded | | Injection Molded | ||
| 47 | | 47 | ||
- | | [[Image:Sponge_Mount.jpg]] | + | | [[Image:Sponge_Mount.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 336: | Line 336: | ||
| Extruded, cut | | Extruded, cut | ||
| 186 | | 186 | ||
- | | [[Image:Mop_Rod.jpg]] | + | | [[Image:Mop_Rod.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 345: | Line 345: | ||
| Purchased | | Purchased | ||
| <1 | | <1 | ||
- | | [[Image:Folding_Handle_Pin.jpg]] | + | | [[Image:Folding_Handle_Pin.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 354: | Line 354: | ||
| Extruded, cut, bent | | Extruded, cut, bent | ||
| 35 | | 35 | ||
- | | [[Image:Folding_Rod.jpg]] | + | | [[Image:Folding_Rod.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 363: | Line 363: | ||
| Extruded, cut, bent | | Extruded, cut, bent | ||
| 51 | | 51 | ||
- | | [[Image:Folding_Plate_Compressor.jpg]] | + | | [[Image:Folding_Plate_Compressor.jpg|150px]] |
|- | |- | ||
| | | | ||
Line 372: | Line 372: | ||
| Injection Molded | | Injection Molded | ||
| 2 | | 2 | ||
- | | [[Image:Folding_Plate_Compressor_Roller.jpg]] | + | | [[Image:Folding_Plate_Compressor_Roller.jpg|150px]] |
|} | |} |
Revision as of 20:34, 5 February 2012
Contents |
Stakeholder Analysis
In performing a product use study the following stakeholders, their needs, and desires were identified and documented.
Stakeholder | Needs | Wants |
---|---|---|
Manufacturers | Low cost, Able to mass produced, Easy to assemble, Environmentally friendly, Easy to store and package | |
Investors | Low cost, Significant innovation, Aesthetics, Large market | |
Retailers | Easy to store, Accessory options, Universal interface, Compatibility, Low cost, Utility | |
Cleaning Supply Companies | Universal interface, compatibility | |
Commercial Consumers | Low cost, Durability, Light Weight, Quiet, Intuitive operation, Ergonomic design, Easy to stow, Easy to clean | |
Independent Consumers | Low cost, Aesthetically pleasing, easy to clean, Storability, Portability, Intuitive operation, Light weight, Durability |
Usage
Product Use Steps
Bucket and Mop Combination
1) Make a mess
2) Fill bucket with water
3) Add recommended amount of cleaning solution
4) Put mop in bucket
5) Move mop to wringer
6) Wring mop out
7) Mop floor (i.e. move back and forth across desired dirty surface)
8) Repeat steps 4-7 until desired cleanliness is achieved
9) Empty bucket
10) Repeat steps 2-3 as desired
Folding Mop
1) Make a mess
2) Obtain a bucket or container
3) Fill bucket with water
4) Add recommended amount cleaning solution
5) Put mop in bucket
6) Slide wringer towards end of mop over bucket
7) Mop floor (i.e. move back and forth across desired dirty surface)
8) Repeat steps 5-7 until desired cleanliness is desired
9) Empty bucket
10) Repeat steps 3-4 as desired
Mechanism
Bill of Materials
Figure 1: Exploded view of complete mop and bucket
Figure 2: Exploded view of wringer sub-assembly
Figure 3: Exploded view of folding mop