Drink Cooler Innovation
From DDL Wiki
(Difference between revisions)
(→Bill of Materials) |
|||
| Line 44: | Line 44: | ||
| align="center" | ABS Plastic | | align="center" | ABS Plastic | ||
| align="center" | Injection Molding | | align="center" | Injection Molding | ||
| - | | | | + | | | [[Image:Lid.png | 100x100px]] |
|- | |- | ||
| Line 54: | Line 54: | ||
| align="center" | Assembled | | align="center" | Assembled | ||
| align="center" | Purchased Part | | align="center" | Purchased Part | ||
| - | | | | + | | | [[Image:Motor.png | 100x100px]] |
|- | |- | ||
| Line 64: | Line 64: | ||
| align="center" | PVC Rigid | | align="center" | PVC Rigid | ||
| align="center" | Injection Molding | | align="center" | Injection Molding | ||
| - | | | | + | | | [[Image:Upper_Motor_Housing.png | 100x100px]] |
|- | |- | ||
| Line 74: | Line 74: | ||
| align="center" | PVC Rigid | | align="center" | PVC Rigid | ||
| align="center" | Injection Molding | | align="center" | Injection Molding | ||
| - | | | | + | | | [[Image:Lower_Motor_Housing.png | 100x100px]] |
|- | |- | ||
| Line 84: | Line 84: | ||
| align="center" | 1060 Alloy | | align="center" | 1060 Alloy | ||
| align="center" | Machining | | align="center" | Machining | ||
| - | | | | + | | | [[Image:Block.png | 100x100px]] |
|- | |- | ||
| Line 94: | Line 94: | ||
| align="center" | Assembled | | align="center" | Assembled | ||
| align="center" | Purchased Part | | align="center" | Purchased Part | ||
| - | | | | + | | | [[Image:Peltier_Cell.png | 100x100px]] |
|- | |- | ||
| Line 104: | Line 104: | ||
| align="center" | Copper | | align="center" | Copper | ||
| align="center" | Machining | | align="center" | Machining | ||
| - | | | | + | | | [[Image:Copper_Plate1.png | 100x100px]] |
|- | |- | ||
| height="25" align="center" | 10 | | height="25" align="center" | 10 | ||
| - | | align="center" | Copper | + | | align="center" | Copper Plate 2 |
| align="center" | Attached to peltier cells and heat sink | | align="center" | Attached to peltier cells and heat sink | ||
| align="center" | 1 | | align="center" | 1 | ||
| Line 114: | Line 114: | ||
| align="center" | Copper | | align="center" | Copper | ||
| align="center" | Machining | | align="center" | Machining | ||
| - | | | | + | | | [[Image:Copper_Plate2.png | 100x100px]] |
|- | |- | ||
| Line 124: | Line 124: | ||
| align="center" | Assembled | | align="center" | Assembled | ||
| align="center" | Purchased Part | | align="center" | Purchased Part | ||
| - | | | | + | | | [[Image:Heat_Sink.png | 100x100px]] |
|- | |- | ||
| Line 134: | Line 134: | ||
| align="center" | ABS Plastic | | align="center" | ABS Plastic | ||
| align="center" | Machining | | align="center" | Machining | ||
| - | | | | + | | | [[Image:Heat_Sink_Mount.png | 100x100px]] |
|- | |- | ||
| Line 144: | Line 144: | ||
| align="center" | Assembled | | align="center" | Assembled | ||
| align="center" | Purchased Part | | align="center" | Purchased Part | ||
| - | | | | + | | | [[Image:Fan.png | 100x100px]] |
|- | |- | ||
| Line 154: | Line 154: | ||
| align="center" | ABS Plastic | | align="center" | ABS Plastic | ||
| align="center" | Injection Molding | | align="center" | Injection Molding | ||
| - | | | | + | | | [[Image:Rotating_Arm.png | 100x100px]] |
|- | |- | ||
| Line 164: | Line 164: | ||
| align="center" | ABS Plastic | | align="center" | ABS Plastic | ||
| align="center" | Injection Molding | | align="center" | Injection Molding | ||
| - | | | | + | | | [[Image:Rotating_Arm_Holder.png | 100x100px]] |
|- | |- | ||
| Line 174: | Line 174: | ||
| align="center" | Rubber | | align="center" | Rubber | ||
| align="center" | Purchased Part | | align="center" | Purchased Part | ||
| - | | | | + | | | [[Image:Rotating_Arm_Bands.png | 100x100px]] |
|- | |- | ||
| Line 184: | Line 184: | ||
| align="center" | ABS Plastic | | align="center" | ABS Plastic | ||
| align="center" | Injection Molding | | align="center" | Injection Molding | ||
| - | | | | + | | | [[Image:Spout.png | 100x100px]] |
|- | |- | ||
| Line 194: | Line 194: | ||
| align="center" | ABS Plastic | | align="center" | ABS Plastic | ||
| align="center" | Purchased Part | | align="center" | Purchased Part | ||
| - | | | | + | | | [[Image:Tubing.png | 100x100px]] |
|- | |- | ||
| Line 204: | Line 204: | ||
| align="center" | ABS Plastic | | align="center" | ABS Plastic | ||
| align="center" | Injection Molding | | align="center" | Injection Molding | ||
| - | | | | + | | | [[Image:Dial.png | 100x100px]] |
|- | |- | ||
| Line 214: | Line 214: | ||
| align="center" | Assembled | | align="center" | Assembled | ||
| align="center" | Purchased Part | | align="center" | Purchased Part | ||
| - | | | | + | | | [[Image:Circuit_Board.png | 100x100px]] |
|- | |- | ||
| Line 224: | Line 224: | ||
| align="center" | Nylon | | align="center" | Nylon | ||
| align="center" | Purchased Part | | align="center" | Purchased Part | ||
| - | | | | + | | | [[Image:Adapter.png | 100x100px]] |
|- | |- | ||
| height="25" align="center" | 22 | | height="25" align="center" | 22 | ||
| - | | align="center" | Pan Head | + | | align="center" | Pan Head Phillips |
| align="center" | Fastener | | align="center" | Fastener | ||
| align="center" | 18 | | align="center" | 18 | ||
| Line 234: | Line 234: | ||
| align="center" | Steel | | align="center" | Steel | ||
| align="center" | Purchased Part | | align="center" | Purchased Part | ||
| - | | | | + | | | [[Image:Pan_Head_Phillips.png | 100x100px]] |
|- | |- | ||
| Line 244: | Line 244: | ||
| align="center" | Steel | | align="center" | Steel | ||
| align="center" | Purchased Part | | align="center" | Purchased Part | ||
| - | | | | + | | | [[Image:Flat_Head_Phillips.png | 100x100px]] |
|} | |} | ||
Revision as of 02:28, 6 May 2012
Executive Summary
Market Analysis
Bill of Materials
| Part Number | Part | Function | Number of parts | Weight (/unit in g) | Material | Manufacturing Process | Images |
| 1 | Inner Housing | Provides surface for attaching components | 1 | 340.2 | ABS Plastic | Injection Molding | 
|
| 2 | Outer Housing | Provides external façade | 1 | 834.6 | ABS Plastic | Injection Molding | 
|
| 3 | Lid | Keeps device closed during operation | 1 | 158.8 | ABS Plastic | Injection Molding | 
|
| 4 | Motor | Powers the flow of water and the rotation of the rod | 1 | 173 | Assembled | Purchased Part | 
|
| 5 | Upper Motor Housing | Houses the motor | 1 | 86.2 | PVC Rigid | Injection Molding | 
|
| 6 | Lower Motor Housing | Houses the motor | 1 | 45.4 | PVC Rigid | Injection Molding | 
|
| 7 | Block with Channels | Provides turbulent flow to water | 1 | 68 | 1060 Alloy | Machining | 
|
| 8 | Peltier Cell | Provides thermo-electric cooling | 2 | 25 | Assembled | Purchased Part | 
|
| 9 | Copper Plate 1 | Attached to aluminium channels and peltier cells | 1 | 285.8 | Copper | Machining | 
|
| 10 | Copper Plate 2 | Attached to peltier cells and heat sink | 1 | 72.6 | Copper | Machining | 
|
| 11 | Heat Sink | Removes heat from peltier cells | 1 | 50 | Assembled | Purchased Part | 
|
| 12 | Heat Sink Mount | Provides platform to mount heat sink | 1 | 40.8 | ABS Plastic | Machining | 
|
| 13 | Fan | Aids heat sink in heat removal from peltier cells | 1 | 20 | Assembled | Purchased Part | 
|
| 14 | Rotating Arm | Rotates drink container | 1 | 9.1 | ABS Plastic | Injection Molding | 
|
| 15 | Rotating Arm Holder | Holds the rotating arm in place | 1 | 15 | ABS Plastic | Injection Molding | 
|
| 16 | Rotating Arm Bands | Provides friction on rotating arm | 5 | <1 | Rubber | Purchased Part | 
|
| 17 | Spout | Provides output for water flow | 1 | 4.5 | ABS Plastic | Injection Molding | 
|
| 18 | Tubing | Connects aluminium bloack to motor housing | 1 | 4.5 | ABS Plastic | Purchased Part | 
|
| 19 | Dial | Provides means to adjust timer | 1 | 9.1 | ABS Plastic | Injection Molding | 
|
| 20 | Circuit Board | Contains product's circuitry | 1 | 0 | Assembled | Purchased Part | 
|
| 21 | Adapter, Tube to Male Threaded Pipe | Provides connections for both ends of the tubing | 2 | <1 | Nylon | Purchased Part | 
|
| 22 | Pan Head Phillips | Fastener | 18 | <1 | Steel | Purchased Part | 
|
| 23 | Flate Head Phillips | Fastener | 8 | <1 | Steel | Purchased Part | 
|
