Paper towel dispenser
From DDL Wiki
(→FMEA Analysis) |
(→DFE Analysis) |
||
Line 440: | Line 440: | ||
== DFE Analysis== | == DFE Analysis== | ||
<br /> | <br /> | ||
+ | |||
+ | The production of a product has an environmental impact from the creation of the parts that make up the product, to the time when the consumer throws the product in the garbage. In our case, we studied the Economic Input-Output Life Cycle Assessment (EIO-LCA) of a paper towel dispenser using Carnegie Mellon's EIO-LCA site. | ||
+ | |||
+ | [[Image:PTD_Conventional_Air_Pollutants.JPG]] | ||
+ | |||
+ | [[Image:PTD_Conventional_Air_Pollutants_Chart.JPG]] | ||
+ | |||
+ | [[Image:PTD_GHG.JPG]] | ||
+ | |||
+ | [[Image:PTD_GHG_Chart.JPG]] | ||
+ | |||
+ | [[Image:PTD_Toxic_Releases.JPG]] | ||
+ | |||
+ | [[Image:PTD_Toxic_Releases_Chart.JPG]] | ||
== Team Member Roles == | == Team Member Roles == |
Revision as of 22:18, 20 September 2009
Contents |
Executive Summary
Stakeholders
There are six major stakeholders with regards to the paper towel dispenser: Manufacturer, retailer, customer, user, society. The main needs for the manufacturer are to reduce cost and create a reliable product. For the retailer, it is being able to sell a quality product. For the customer, it is making sure it is an affordable and reliable machine. For the customer, cleanliness and ease of use are paramount. For the maintenance worker, ease of opening and replacing the paper towel are important. Society plays a role with regards to how the use of paper towel affects the ecosystem and earth in general. Listed below are the stakeholders and their respective needs.
Paper Towel Manufacturer
- Material cost
- Manufacturing cost
- Assembly
- Transporting
- Standardize/minimize parts
Retailer
- Cost
- Storage
- Reliability
- Usability
- Transporting
Customer
- Cost
- Mounting
- Ease of use
- Reliability
- Aesthetics
- Safety
User
- Ease of use / ergonomics
- Speed of operation
- Aesthetics
- Cleanliness
- Safety
Maintenance Worker
- Ease of towel replacement
- Safety
Society
- Environment
Usability Study
Assembly Pictures
How it Works
Mechanical Analysis
Parts List
DFMA Analysis
Design For Manufacture
Design For Assembly
FMEA Analysis
Failure mode and effects analysis (FMEA) identifies potential problems of every component in the machinery, lists their effects on the system, and finally provides recommended actions to prevent such failures. The methodology for problem identification depends on ratings of Severity of a failure (S), Occurrence of Failure (O), and Detection of Failure (D). These scales are between 1 and 10 and they are rated in a way that less number of ratings indicates less significant problem and conversely higher rating means more serious failure or effect. The results of a FMEA Analysis (RPN) are calculated by multiplying S, O and D to signify seriousness of the problem.
Conclusion
Part No. | Name | Function | Failure Mode | Effects of Failure | S | Causes of Failure | O | Design Controls | D | RPN | Recommended Actions | Responsibility |
---|---|---|---|---|---|---|---|---|---|---|---|---|
01 | Front Housing | Protects device from exterior | Fractures, Warped |
| 7 |
| 4 |
| 2 | 56 |
| Reliability
|
02 | Front Housing Clip | Holds housings together | Bends |
| 4 |
| 2 |
| 6 | 48 |
| Assembly and Reliablity
|
03 | Front Housing Tab | Secures housing clip | Strips |
| 2 |
| 2 |
| 8 | 32 |
| Assembly
|
04 | Rear Housing | Holds mechanical components | Fractures |
| 7 |
| 4 |
| 9 | 252 |
| Reliability |
05 | Paper Towel Holding Arm | Holds paper towel roll | Bends |
| 6 |
| 3 |
| 2 | 36 |
| Assembly and Manufacturing |
08 | Screw Anchor | Holds screw in wall | Fractures |
| 7 |
| 6 |
| 8 | 336 |
| Reliablity |
09 | Paper Guide Tube | Guides paper towel to cutting cylinder | Failed |
| ||||||||
10 | Spring (uneven hooks) | Holds 09 in place | Deformed |
| 3 |
| 2 |
| 5 | 30 |
| Assembly and Reliablity |
11 | Spring (even hooks) | Holds lever to spindle housing | Deformed |
| 3 |
| 2 |
| 4 | 24 |
| Assembly and Reliablity |
14 | Locking Spring | Hides screw in turning wheel | Deformed |
| 3 |
| 2 |
| 4 | 24 |
| Assembly and Reliablity |
16 | Guide clips for 09 | Guides paper on 09 | text | text | ||||||||
18 | Lever Arm | Connects spring to spindle | Breaks |
| 5 |
| 2 |
| 2 | 20 |
| Manufacturing and Reliablity |
19 | Spring Connector | Connects two springs to lever arm | Breaks |
| 5 |
| 2 |
| 3 | 30 |
| Assembly and Reliablity |
20 | Rounded Spring Guide | Angles spring to desired measurement | Breaks |
| 2 |
| 2 |
| 7 | 28 |
| Manufacturing |
21 | Thin Paper Guide | Guides paper out of device | Breaks |
| 4 |
| 3 |
| 1 | 12 |
| Manufacturing |
22 | Front Spindle Housing | Final housing before paper leaves device | Fractures |
| 3 |
| 2 |
| 6 | 36 |
| Assembly and Manufacturing |
23 | Spindle Housing Back | Back of spindle housing | Fractures |
| 3 |
| 2 |
| 6 | 36 |
| Assembly and Manufacturing |
24,25 | Spindle Housing (L,R) | Sides of spindle housing | Breaks |
| 5 |
| 2 |
| 6 | 60 |
| Assembly and Manufacturing |
29 | White Teeth Guide/Arm | Guides cutting teeth in spindle | Breaks |
| 3 |
| 3 |
| 6 | 36 |
| Assembly and Manufacturing |
30 | Cutting Teeth | Back of spindle housing | Wears,Bends |
| 4 |
| 2 |
| 2 | 16 |
| Manufacturing |
31,32 | Spindle | Back of spindle housing | Warps,Breaks |
| 5 |
| 1 |
| 3 | 15 |
| Assembly and Manufacturing |
DFE Analysis
The production of a product has an environmental impact from the creation of the parts that make up the product, to the time when the consumer throws the product in the garbage. In our case, we studied the Economic Input-Output Life Cycle Assessment (EIO-LCA) of a paper towel dispenser using Carnegie Mellon's EIO-LCA site.
Team Member Roles
- Eric Totong:
- Chang Keun Jung:
- James Li-Yang Lee:
- Nishan Kulatilaka: