Remote control tarantula
From DDL Wiki
(Difference between revisions)
(→Function) |
(→Function) |
||
Line 6: | Line 6: | ||
TEST | TEST | ||
+ | <br /> | ||
TEST | TEST | ||
+ | <br /> | ||
TEST | TEST | ||
+ | <br /> | ||
TEST | TEST | ||
+ | <br /> | ||
TEST | TEST | ||
+ | <br /> | ||
TEST | TEST | ||
+ | <br /> | ||
TEST | TEST | ||
+ | <br /> | ||
TEST | TEST | ||
+ | <br /> | ||
TEST | TEST | ||
+ | <br /> | ||
TEST | TEST | ||
+ | <br /> | ||
TEST | TEST | ||
+ | <br /> | ||
TEST | TEST | ||
Revision as of 11:15, 21 September 2007
Contents |
Executive summary
Customer needs
Function
TEST
TEST
TEST
TEST
TEST
TEST
TEST
TEST
TEST
TEST
TEST
TEST
Product use
Components
Part # | Part name | QTY | Function | Materials | Manufacturing Process | Picture |
---|---|---|---|---|---|---|
001 | Cover Screws | 13 |
| Steel | Cold headed, Thread Rolled | |
002 | Inner Flat-headed screw | 2 |
| Steel | Cold headed, Thread rolled | |
003 | Battery Cover | 1 |
| Plastic | Injection Molded, hand modified | |
004 | Back Wheel housing | 1 |
| Plastic | Injection Molded | |
005 | Back Wheel | 2 |
| Plastic | Injection Molded, smoothed | |
006 | Small Leg | 4 |
| Plastic | Injection Molded | |
007 | Medium Leg | 2 |
| Plastic | Injection Molded | |
008 | Large leg | 2 |
| Plastic | Injection Molded | |
009 | Feelers | 2 |
| Plastic | Injection Molded | |
010 | Driving Wheel 1 | 1 |
| Plastic | Injection Molded, smoothed | |
011 | Driving Wheel 2 | 1 |
| Plastic | Injection Molded, smoothed | |
012 | Plastic Protection housing | 1 |
| Plastic | Injection Molded | |
013 | Back Wheel Axle | 2 |
| Steel | Cut wire, smoothed | Image:RC Tarantula Part 013.jpg |
014 | Battery Cover Washer | 1 |
| Plastic | Punched | Image:RC Tarantula Part 014.jpg |
015 | Gear 1 | 2 |
| Plastic | Injection Molded | |
016 | Gear 2 | 1 |
| Plastic | Injection Molded | |
017 | Gear 3 | 2 |
| Plastic | Injection Molded | |
018 | Gear 4 | 1 |
| Plastic | Injection Molded | |
019 | Axle 1 | 1 |
| Steel | Cut wire, smoothed | |
020 | Axle 2 | 1 |
| Steel | Cut wire, smoothed | |
021 | Axle 3 | 1 |
| Steel | Cut wire, smoothed | |
022 | Axle 4 | 1 |
| Steel | Cut wire, smoothed, stamped rough areas | |
023 | Axle 5 | 1 |
| Steel | Cut wire, smoothed, stamped rough areas | |
024 | Axle Cap | 1 |
| Plastic | Injection Molded | Image:RC Tarantula Part 024.jpg |
025 | Switch Assembly | 1 |
| Circuit Board (silicon), metal wires, plastic switch | Assembly | |
026 | Switch Cover | 1 |
| Plastic | Injection Molded | |
027 | Motor Assembly | 1 |
| Metal wiring, magnets, Metal casing, plastic gearing | Assembly | |
028 | Circuit Board Assembly | 1 |
| Circuit Board (silicon), metal wires | Assembly | |
029 | LED Assembly | 1 |
| Circuit (silicon), metal wires, LED | Assembly | |
030 | Tarantula exterior bottom | 1 |
| Plastic | Injection Molded, hand modified | |
031 | Tarantula exterior top | 1 |
| Plastic | Injection Molded, hand modified | |
032 | Battery Connector | 1 |
| Steel | Cut sheet metal | Image:RC Tarantula Part 032.jpg |
033 | Battery + connector | 1 |
| Steel | Cut sheet metal | Image:RC Tarantula Part 033.jpg |
034 | Battery - connector | 1 |
| Steel | Cut sheet metal | Image:RC Tarantula Part 034.jpg |
035 | Metal screw receiver | 1 |
| Steel | threaded cylinder | Image:RC Tarantula Part 035.jpg |
036 | Drive Wheel Mount | 1 |
| Plastic | Injection Molded |