Keg tap
From DDL Wiki
Contents |
Executive Summary
- Describes key findings and recommendations
Major Stakeholders and Product Needs
- Identify major post-production stakeholders and list major product needs for each
Usage
- Document in detail how the product is used, step by step, and summarize findings from your user studies.
Bill of Materials
- Also identify standard purchase parts.
Keg Tap Components
Assembly Diagrams
- Include pictures of the assembly with all components labeled
Mechanical Function
- Document how the system functions mechanically
Design for Manufacturing and Assembly (DFMA)
- Highlight findings and opportunities for improvement, identifying where our competitor has followed guidelines and made good choices.
- In particular, are there opportunities to improve manufacturability and make a competing product cheaper? Identify where material and process choices are appropriate or inappropriate for expected production volume.
This particular keg tap consists of 26 distinct parts. The majority of the metal pieces are made from stainless steel, with the exception of three that are made from brass. All three of the brass pieces are interior components. The non-metal components are made from plastic and rubber.
All of the metal components are shaped using a deformation process except for the base, which is cast. Casting is a logical manufacturing choice for this piece because of its relatively complex shape. The other main metal parts are extruded, then machined. Machining includes removing material with a lathe or milling machine, drilling holes, cutting threads, and grinding down sharp edges. The amount of machining involved in the manufacturing process for this product is acceptable for low to medium volume production.
keg tap was manufactured with a low to medium volume production in mind. For a larger production volume, the manufacturing would need a complete overhaul. Sand casting is suitable for medium volume production.
All parts are joined by threads or snapped on (o-rings). This saves machine cost in manufacturing, but may take more time (most likely assembled by hand in an assembly line). Joining method good for the consumer because you can take the tap apart to clean it; also replace parts if need be. A common failure mode may be o-ring fatigue; these parts could easily be replaced instead of buying a new tap.
DFM minimize part count standardize components standardize design features keep design simple multifunctional parts ease of fabrication avoid tight tolerances minimize secondary & finishing operations
DFA minimize part count minimize assembly surfaces mistake-proof minimize fasteners
Failure Modes and Effects Analysis (FMEA)
- Highlight findings and opportunities for improvement, indentifying where our competitor has followed guidelines and made good choices.
- In particular, are there important failure modes that should be considered in a redesign or a new design? Focus on use phase, rather than manufacturing.
Part # | Item | Function | Failure Mode | Effects of Failure | S | Cause of Failure | O | Design Controls | D | RPN | Recommended Actions |
---|---|---|---|---|---|---|---|---|---|---|---|
1 | Black Ball | Grip for Pumping | Could be Unscrewed and Lost | Uncomfortable Pumping | Unaware Users | Make sure the ball is screwed on tightly | Apply Loctite | ||||
2 | Plunger | Forces Air into Keg | This part is very robust. Cannot foresee any failure modes. | ||||||||
3 | Plunger Disc | Air Tight | This part is very robust. Cannot foresee any failure modes. | ||||||||
3.1 | O-Ring | Seal | O-ring becomes hardened | Loss of air tight seal for pressurizing keg | Repeated use and time | Oil the o-ring | Sell spare parts | ||||
4 | Cylindrical Plunger Casing | Supply Keg with Pressure | Dent in the casing, burs, scratches, rust on the inside of the casing | Plunger cannot be moved inside the case, o-ring gets torn up | Misuse, Dropping the tap | All these pieces are robust enough | None | ||||
5 | Cylindrical Top | Encloses Plunger in Casing | Top comes unscrewed | Cannot pressurize keg | Human tampering | Check that it is screwed on tightly | None, gluing these threads makes disassembly harder | ||||
6 | Plunger Spring | Prevents Plunger from Getting Stuck | Breaks | Plunger, though unlikely, may get stuck at top of casing | Misuse or fatigue | Make sure spring can handle forces | Sell spare parts | ||||
7 | Center Cylinder | Separates Air Input from Beer Output | 1)Leaks beer at the connection point with hose
2)Creates turbulence in beer flow | 1)Loss of beer
2)Foamy beer | 1)Sealant on threads is old
2)Manufacturing | 1)Check that their are no leaks
2)Their Design | 1)None
2)Look into some other way to transition into tubing | ||||
7.1 | O-Ring | Seal | O-ring becomes hardened | Loss of air tight seal for pressurizing keg | Repeated use and time | Oil the o-ring | Sell spare parts | ||||
8 | Lever | Attaches Tap and Keg allowing the flow of beer | This part is very robust. Cannot foresee any failure modes. | ||||||||
8.1 | Lever Casing | Grip for user | Breaks | Unable to attach tap to keg | Ridiculous Misuse | Make sure the part is strong enough | None | ||||
8.2 | White Cap | Aesthetics | Could break or get lost | None | Misuse or overuse | Check this fit | None | ||||
8.3 | Lever Spring | Helps lock tap in two certain positions | Impact fatigue | Unable to lock tap into open position on keg | User misuse | Make sure spring can handle forces | Brainstorm new ways to lock tap | ||||
8.4 | Center Rod | Helps hold handle together | This part is very robust. Cannot foresee any failure modes. | ||||||||
8.5 | Nut | Helps hold handle together | Could come unscrewed | Unable to use tap | Repeated use | Make sure it is screwed on the whole way | None | ||||
8.6 | Washer | Helps hold handle together | Cannot foresee any failure modes | ||||||||
9 | Lever Pin | Attaches the lever to the base and acts as a pivot point for the lever | No foreseen failure modes. | ||||||||
10 | Base | Attaches to Keg | Threads become crooked | Unable to connect tap to keg | Terrible misuse | Threads are very robust | Sell spare parts | ||||
10.1 | O-Ring | Seal | O-ring becomes hardened | Loss of air tight seal for pressurizing keg | Repeated use and time | Oil the o-ring | Sell spare parts | ||||
11 | Hose | Transfers Beer from Tap to Cup | 1)Hole
2)Kink | 1)Beer is lost
2)Beer cannot reach its destination | 1)Not taking care of tap
2)Jokes | Make sure the tubing is the right kind | None | ||||
12 | Nozzle | Releases Beer from Hose | No foreseen failure mode | ||||||||
12.1 | Handle | Allows the user to start and stop the flow of beer | Deform/Break | Beer would not be allowed to come out the nozzle | Pushing the handle past where it should be | Use thick enough plastic | Sell spare parts | ||||
12.2 | White Plastic Center | Connects nozzle handle to cap seal | Connection point to nozzle handle breaks | Beer can not come out of nozzle | Pushing the handle past where it should be | Test to make sure it operates the way it should | Sell spare parts, look for a possible redesign | ||||
12.3 | Spring | Apply extra force to keep the pressurized beer from coming out of the keg | No foreseen failure modes | ||||||||
12.4 | Cap Seal | Blocks the flow from leaving the hose | Surface fatigue wear | Beer would leak through and leave the nozzle | Repeated use | Make sure the rubber used can withstand many cycles | Sell spare parts | ||||
12.5 | Hard Plastic Cap | Connects the Handle to the nozzle | Fracture | Nozzle/Handle would not be able to function | Over tightening the cap onto the nozzle | Tighten cap enough so users do not have to | Sell spare parts
|
Design for Environment (DFE)
- Highlight findings and opportunities for improvement, indentifying where our competitor has followed guidelines and made good choices.
- In particular, if Congress were to pass a tax on CO2, would this have a significant impact on the cost of production or use of the product?
Manufacturing
- Greenhouse Gas Emissions
When an additional $1 million dollars is spent in the Miscellaneous fabricated metal product manufacturing sector, greenhouse gas emissions rise by approximately 796 metric tons of CO2 Equivalent (MTCO2E). The data shows that the majority of the gases are produced by power generation and supply, iron and steel mills, and transportation. The actual sector that produces the tap only produces 42.6 MTCO2E, which is small considering the amount released in other sectors.
- Toxic Releases
An additional $1 million dollars spent in the sector for keg taps results in a rise in total toxic releases of 1590kg. The primary contributors to these releases are mining of: copper, nickel, lead, and zinc gold, silver, and other metal ore mining. The Miscellaneous fabricated metal product manufacturing sector only amounts to a 57.1 kg increase in toxic releases.
Use
Using the template of Professor Michalek's "EIO-LCA example: coffeemaker" we did a comparison of the emissions associated with the use of the product versus the manufacturing of it. Since the keg tap itself is manually operated the power input is not applicable, but there are other products that are used with the keg tap. Foremost, is beer from a keg and we assumed that this product would be used to the extremes, like a fraternity would use it. We decided this too see what the maximum impact would be of using 520 kegs over a 5 year lifetime window. Secondly, solo cups are a necessity so we included them as well, assuming 100 cups used per keg.
Based on the data above, it is clear that the manufacturing of our tap has next to no environmental impact compared to the manufacturing of plastic cups and especially to the brewing process.
End of life
Our product is composed of only metal and plastic, both of which can be recycled. So once our product can no longer perform as intended it can be recycled in a few ways. Some parts are almost impossible to break and can be used again as is and just reassembled with parts that needed to be replaced. The pieces that break can be melted down and reused in some way, whether they are plastic or metal.
DFE Conclusions
Based on the numbers provided in figure ## it would be wise for our group to emphasize on trying to reduce wasting beer because it is the largest component of greenhouse gas emissions associated with our product. A large amount of foam is produced in transport and distribution of the beer in a keg and it is normally thrown away. If we could reduce the foam created we could in turn reduce the environmental impact that our product is associated with.
Mechanical Analysis
- Include mechanical analysis to support quantitative understanding of the product's most critical mechanical aspects. Indluce a free body diagram, and be sure to define all symbols and explain all equations used.
Team Member Roles
- Identify team member roles during this phase and summarize your process. Submit individual peer evaluations to Prof.