| Sr. No.
| Part
| Function
| Number of parts
| Weight of 1 part (g)
| Material
| Manufacturing Process
| Standard Part
|
|
|
|
|
|
|
|
|
|
| 1
| Water Spout Assembly
|
|
|
|
|
|
|
| a
| Spout
| Ejects pumped up water
| 1
| 5
| Plastic
| Injection Molding
| No
|
| b
| Screw
| Fastner
| 2
| <1
| Steel
| Purchased Part
| Yes
|
| c
| Washer
| Distribute load of fastner
| 2
| <1
| Rubber
| Purchased Part
| Yes
|
|
|
|
|
|
|
|
|
|
| 2
| Bottom Assembly
|
|
|
|
|
|
|
| a
| Rubber Rest
| Prevents shaking of the overall part
| 6
| <1
| Rubber
| Molding
| No
|
| b
| Screw
| Fastner
| 8
| <1
| Steel
| Purchased Part
| Yes
|
| c
| Bottom Cover
| Cover that comes off the bottom
| 1
| 121
| Plastic
| Injection Molding
| No
|
| d
| Spring
| Damp vibrations of the entire machine
| 2
| <1
| Steel
|
| Yes
|
| e
| Sealant Gel
| Prevents leakage of water
|
| <1
|
|
| Yes
|
|
|
|
|
|
|
|
|
|
| 3
| Rotary Bar Assembly
|
|
|
|
|
|
|
| a
| Plastic Bar
| Rotates can/bottle once placed
| 1
| 16
| Plastic
| Injection Molding
| No
|
| b
| Screw
| Fastner
| 2
| <1
| Steel
|
| Yes
|
| c
| Holder
| Keeps bar in place
| 1
| <1
| Plastic
| Injection Molding
| No
|
| d
| O rings
|
| 7
| <1
| Rubber
|
| No
|
|
|
|
|
|
|
|
|
|
| 4
| Circuiting - Electronics
|
|
|
|
|
|
|
| a
| Plastic Timer
| Varies how long motor runs
| 1
| 21
| Plastic
| Injection Molding
| No
|
| b
| Spring
|
| 1
| <1
| Steel
|
| Yes
|
| c
| Circuit Board
| Contains the controlling
| 1
| 43
|
| Assembled
| No
|
| d
| Screw
| Fastner
| 1
| <1
| Steel
|
| Yes
|
| e
| Metal Piece
|
| 1
| <1
|
| Stamped Sheet Metal
|
|
| f
| Limit Switch
| Ensures that machine does not operate until lid is closed
| 1
| 7
|
| Assembled
| No
|
|
|
|
|
|
|
|
|
|
| 5
| Lid Assembly
|
|
|
|
|
|
|
| a
| Lid
| Covers the top of the product(must be shut to run)
| 1
| 27
| Plastic
| Injection Molding
| No
|
| b
| Torsion Spring
| Automatically opens the lid if not clicked in
| 2
| <1
| Steel
|
| Yes
|
| c
| Screw
| Fastner
| 2
| <1
| Steel
|
| Yes
|
| d
| Plastic Casing
| Forms a casing for the the torsional springs
| 2
| <1
| Plastic
| Injection Molding
|
|
| e
| White Plastic Pieces
| Hold Torsional Springs
| 2
| 2
| Plastic
| Injection Molding
| No
|
| f
| Spring
|
| 2
| <1
| Steel
|
|
|
| g
| Button
| Clicks when lid is shut
| 1
| <1
| Plastic
| Injection Molding
| No
|
|
|
|
|
|
|
|
|
|
| 6
| Bottom Drain Assembly
|
|
|
|
|
|
|
|
| Drain
| Water flows through from here to pump
|
|
| Plastic
| Injection Molding
| No
|
| a
| Drain Cap
| Prevents ice from entering
| 1
| 4
| Plastic
| Injection Molding
| No
|
| b
| Screw
| Fastner
| 2
| <1
| Steel
|
| Yes
|
|
|
|
|
|
|
|
|
|
| 7
| Housing of the entire product
|
| 1
| 697
| Plastic
| Injection Molding
| No
|
|
|
|
|
|
|
|
|
|
| 8
| Motor Assembly
|
|
|
|
|
|
|
| a
| Motor
| For pumping water and Running rotating bar
| 1
| 173
|
| Assembled
| No
|
| b
| Drain Channel
| Channels water towards the motor
| 1
| 21
| Plastic
| Injection Molding
| No
|
| c
| Lower Housing
| Houses Motor and provides passage for the flow of water
| 1
| 14
| Plastic
| Injection Molding
| No
|
| d
| Middle Housing
| 1
| 44
| Plastic
| Injection Molding
| No
|
| e
| Upper Housing
| 1
| 17
| Plastic
| Injection Molding
| No
|
|
|
| Connects drain channel to the L-shaped joint
|
| 13
| Rubber
| Extrusion Molding
| No
|
| g
| L-shaped joint
| Connects the Drain Channel to the Rubber Tube
| 1
| 9
| Plastic
| Injection Molding
| No
|
| h
| Circular Plate
| Rotates Under Motor
| 1
| 1
| Plastic
| Injection Molding
| No
|
| i
| Metal Holder
| Metal Holder
| 2
| 1.5
|
|
| No
|
| j
| Belt
| Transfers rotational motion to the Shaft
| 1
| <1
| Rubber
|
| No
|
| k
| Bevel Gear
| Transfers rotational motion to the Belt
| 1
| 8
| Plastic
| Injection Molding
| Yes
|
| m
| Screws
| Fastner
| 2
| <1
| Steel
|
| Yes
|
| n
| Washers
|
| 3
| <1
| Rubber
|
| Yes
|
| o
| Plastic Shaft
|
| 1
| 3
| Plastic
| Injection Molding
| No
|
| p
| Metal Shaft
|
| 1
| 2
|
|
| No
|
