Coffeemaker
From DDL Wiki
Contents |
Parts List
The following table is a list of all the parts that come out of the coffeemaker.
Bill of Materials
The following is a table of individual components, assemblies and certain off the shelf parts that we took apart during our dissection process of the coffeemaker.
Part Number | Name | QTY | Weight (g) | Function | Material | Manufacturing Process | Image |
---|---|---|---|---|---|---|---|
1 | Cubic Peg for Metal Strip | 1 | |||||
2 | Screw for the Glass Container | 1 | |||||
3 | Lid for the Glass Container | 1 | |||||
4 | Metal Strip for the Glass Container | 1 | |||||
5 | Handle for the Glass Container | 1 | |||||
6 | Filter Lever | 1 | |||||
7 | Filter Spring | 1 | |||||
8 | White Filter Rubber Piece | 1 | Rubber | Injection Molding | |||
9 | Filter | 1 | |||||
10 | Plastic Lid | 1 | Plastic | ||||
11 | Cardboard Piece | 1 | Cardboard | ||||
12 | Bottom Screws | 5 | |||||
13 | Plastic Bottom Lid | 1 | |||||
14 | Plastic Ring | 1 | Plastic | Injection Molding | |||
15 | Insulator Rubber Band | 1 | Rubber | Injection Molding | |||
16 | Heater Plate | 1 | |||||
17 | Heater Plate Screw | 1 | |||||
18 | Rectangular Lid Piece | 1 | |||||
19 | Rubber Tube Rings | 4 | Tighten and put the tubes in place | Copper | |||
20 | Heater Bar | 1 | |||||
21 | Heater | 1 | Heat both the water and the container | Aluminum | Casting | ||
22 | Resistor Piece | 1 | Part of the heater circuit | Assembly | Off Shelf | ||
23 | Little Screw for Plastic Wire Piece | 2 | |||||
24 | Slightly Larger Screw for Heater | 1 | |||||
25 | Nut for Heater Screw | 1 | Holds the Heater in Position | ||||
26 | Plastic Piece for Wires | 1 | |||||
27 | Smaller Screw | 5 | |||||
28 | Washer for Smaller Screw | 5 | |||||
29 | Top-Bottom Connection Screw | 3 | Connect the top and bottom half of the coffeemaker | ||||
30 | Lid Lever | 1 | Support the lid | Plastic | Injection Molding | ||
31 | Plastic Volume Meter | 1 | Meter of the coffeemaker | Plastic | Injection Molding | ||
32 | Lid Hinge Connected to Tubes | 1 | Connection between the lid and tubes | Plastic | Injection Molding | ||
33 | Transparent Tube | 1 | Rubber | Injection molding | |||
34 | Opaque Tube | 2 | |||||
35 | Red Ball | 1 | Part of the valve in the opaque tube | Plastic | Injection Molding | ||
36 | Base of Switch | 1 | Base of the switch | ||||
37 | Switch | 1 | Control on/off of the coffeemaker | Plastic | Injection Molding | ||
38 | Tiny Spring | 1 | Part of the switch | Off Shelf | |||
39 | Tiny Piece from the Switch | 1 | Part of the switch | ||||
40 | Red Heating Connection | 2 | |||||
41 | Wires Coming out from the Heater | 2 | Rubber and Copper | Off Shelf | |||
42 | White Capacitor Screw | 2 | Put the capacitor in place | ||||
43 | Washer for Capacitor Screw | 2 | Washer for screw | Aluminum | Off Shelf | ||
44 | N label | 1 | Label negative of the circuit | plastic tape | Off Shelf | ||
45 | Switch with Three Wires | 1 | Inside part of the switch | Assembly | Off Shelf | ||
46 | Blue Wire | 1 | Off Shelf | ||||
47 | White Wire | 1 | Off Shelf | ||||
48 | Black Wire | 1 | Off Shelf | ||||
49 | Glass Container | 1 | Coffee Container | Glass | |||
50 | Top Part of Body | 1 | Top half of the coffeemaker | Plastic | Injection Molding | ||
51 | Bottom Part of Body | 1 | Bottom half of the coffeemaker | Plastic | Injection Molding |
Design For Manufacturing and Assembly (DFMA)
Failure Modes and Effects Analysis (FMEA)
Design for Environment (DFE)
Group 8 Team Members
Lucas Neffa
Andrew Vickory
Nick Ciesielski
Yang Wen
Kaifu Wang
References
Dieter, George E., and Linda C. Schmidt. Engineering Design. 4th Edition. New York, NY: McGraw-Hill, 2009. Print.