Windshield wipers

From DDL Wiki

(Difference between revisions)
Jump to: navigation, search
Line 4: Line 4:
|-  
|-  
! 1
! 1
-
| Motor Connection Nut || 1 || 6 || Holds the entire wiper assembly to the motor || Cast || [[Image:motor connection nut.jpg|100 px]]
+
| colspan="3"|Motor Connection Nut || 1 || 6 || Holds the entire wiper assembly to the motor || Cast || [[Image:motor connection nut.jpg|100 px]]
|-  
|-  
! 2  
! 2  
-
| Motor Connection Link (1L) || 1 || 62 || Link connecting the spinning motor to Link 1 || Cast, with the knob pressed into it || [[Image:motor connection link.jpg|100 px]]  
+
| colspan="3"|Motor Connection Link (1L) || 1 || 62 || Link connecting the spinning motor to Link 1 || Cast, with the knob pressed into it || [[Image:motor connection link.jpg|100 px]]  
|-  
|-  
! 3  
! 3  
-
| Link 1 (LN3) || 1 || 158 ||  || Cast, with the knobs pressed into it || [[Image:Link 1 (LN3).jpg|100 px]]  
+
| colspan="3"|Link 1 (LN3) || 1 || 158 ||  || Cast, with the knobs pressed into it || [[Image:Link 1 (LN3).jpg|100 px]]  
|-  
|-  
! 4  
! 4  
-
| Rubber Connections || 2 || Unable to detach || Caps on  Link 1 that are used to attach to the metal knobs in the connection links  || Injection molded and pressed onto the link || [[Image:rubber connection.jpg|100 px]]  
+
| colspan="3"|Rubber Connections || 2 || Unable to detach || Caps on  Link 1 that are used to attach to the metal knobs in the connection links  || Injection molded and pressed onto the link || [[Image:rubber connection.jpg|100 px]]  
|-  
|-  
!   
!   
-
| WIPER CONNECTION SUBASSEMBLY 1 ||  ||  ||  || || [[Image:wiper connection subassembly 1.jpg|100 px]]  
+
| colspan="3"|WIPER CONNECTION SUBASSEMBLY 1 ||  ||  ||  || || [[Image:wiper connection subassembly 1.jpg|100 px]]  
|-  
|-  
! 5  
! 5  
-
|   Rubber cap || 1 || 0 || Rubber cap that goes over the wiper connection point in the subassembly || Injection molded, loose fit || [[Image:ww-rubber cap.jpg|100 px]]  
+
| || colspan="2"| Rubber cap || 1 || 0 || Rubber cap that goes over the wiper connection point in the subassembly || Injection molded, loose fit || [[Image:ww-rubber cap.jpg|100 px]]  
|-  
|-  
! 6  
! 6  
-
|    Hex Screws || 3 || 7 (#7+#8) || Screw to bolt wiper connection subassembly into car || Cast || [[Image:ww-hex screws.jpg|100 px]]  
+
|    ||colspan="2"|Hex Screws || 3 || 7 (#7+#8) || Screw to bolt wiper connection subassembly into car || Cast || [[Image:ww-hex screws.jpg|100 px]]  
|-  
|-  
! 7  
! 7  
-
|   Washers || 3 || 7 (#7+#8) || Washers to go with hex screws || Cast || [[Image:ww-washer.jpg|100 px]]  
+
|   ||colspan="2"| Washers || 3 || 7 (#7+#8) || Washers to go with hex screws || Cast || [[Image:ww-washer.jpg|100 px]]  
|-  
|-  
! 8  
! 8  
-
|   Rubber thermal mount || 1 || 31 || Rubber around subassembly to allow for mounting || Injection Molded || [[Image:ww-rubber mount.jpg|100 px]]  
+
|   ||colspan="2"| Rubber thermal mount || 1 || 31 || Rubber around subassembly to allow for mounting || Injection Molded || [[Image:ww-rubber mount.jpg|100 px]]  
|-  
|-  
!   
!   
-
| colspan="2"|  RIGID SUBASSEMBLY  ||  || All pieces in this subassembly are still attached together and therefore do not have individual pictures.  We determined the components by observations ||  || [[Image:ww-rigid subassembly.jpg|100 px]]  
+
| ||colspan="2"|  RIGID SUBASSEMBLY  ||  || All pieces in this subassembly are still attached together and therefore do not have individual pictures.  We determined the components by observations ||  || [[Image:ww-rigid subassembly.jpg|100 px]]  
|-  
|-  
! 9  
! 9  
-
| 7L Link || 1 ||  || Connection to N2 Link 2, which causes the wipers to move || Cast, with the metal pin pressed in ||   
+
| || || 7L Link || 1 ||  || Connection to N2 Link 2, which causes the wipers to move || Cast, with the metal pin pressed in ||   
|-  
|-  
! 10
! 10
-
| Pin || 1 ||  || Pin that acts as the connection point to N2 Link 2 || Cast, pressed into 7L Link ||   
+
| || ||Pin || 1 ||  || Pin that acts as the connection point to N2 Link 2 || Cast, pressed into 7L Link ||   
|-  
|-  
! 11
! 11
-
| Press Fit Ring || 1 ||  || Ring around the cylindrical shaft || Molded, press fit onto shaft ||   
+
| || ||Press Fit Ring || 1 ||  || Ring around the cylindrical shaft || Molded, press fit onto shaft ||   
|-  
|-  
! 12  
! 12  
-
| Washer || 1 ||  || Washer around shaft || Cast ||  
+
| || ||Washer || 1 ||  || Washer around shaft || Cast ||  
|-  
|-  
! 13
! 13
-
| Cylindrical Rings || 2 ||  || Two metal rings around the shaft of the assembly that allows for rotations, act like bearings || Cast, loose fit atop grease to allow for rotation ||   
+
| || ||Cylindrical Rings || 2 ||  || Two metal rings around the shaft of the assembly that allows for rotations, act like bearings || Cast, loose fit atop grease to allow for rotation ||   
|-  
|-  
! 14
! 14
-
| Cap || 1 ||  || Cap on top of shaft that holds the shaft pieces together || Cast, press fit together with shaft ||   
+
| || ||Cap || 1 ||  || Cap on top of shaft that holds the shaft pieces together || Cast, press fit together with shaft ||   
|-  
|-  
! 15
! 15
-
| N2 Link 2 || 1 || 31 || Rubber around subassembly to allow for mounting || Injection Molded || [[Image:ww-rubber mount.jpg|100 px]]  
+
| colspan="3"|N2 Link 2 || 1 || 31 || Rubber around subassembly to allow for mounting || Injection Molded || [[Image:ww-rubber mount.jpg|100 px]]  
|}
|}

Revision as of 13:47, 23 September 2007

Part # Part Name Quantity Weight (grams) Function Manufacturing Process Picture
1 Motor Connection Nut 1 6 Holds the entire wiper assembly to the motor Cast
2 Motor Connection Link (1L) 1 62 Link connecting the spinning motor to Link 1 Cast, with the knob pressed into it
3 Link 1 (LN3) 1 158 Cast, with the knobs pressed into it
4 Rubber Connections 2 Unable to detach Caps on Link 1 that are used to attach to the metal knobs in the connection links Injection molded and pressed onto the link
WIPER CONNECTION SUBASSEMBLY 1
5 Rubber cap 1 0 Rubber cap that goes over the wiper connection point in the subassembly Injection molded, loose fit
6 Hex Screws 3 7 (#7+#8) Screw to bolt wiper connection subassembly into car Cast
7 Washers 3 7 (#7+#8) Washers to go with hex screws Cast
8 Rubber thermal mount 1 31 Rubber around subassembly to allow for mounting Injection Molded
RIGID SUBASSEMBLY All pieces in this subassembly are still attached together and therefore do not have individual pictures. We determined the components by observations
9 7L Link 1 Connection to N2 Link 2, which causes the wipers to move Cast, with the metal pin pressed in
10 Pin 1 Pin that acts as the connection point to N2 Link 2 Cast, pressed into 7L Link
11 Press Fit Ring 1 Ring around the cylindrical shaft Molded, press fit onto shaft
12 Washer 1 Washer around shaft Cast
13 Cylindrical Rings 2 Two metal rings around the shaft of the assembly that allows for rotations, act like bearings Cast, loose fit atop grease to allow for rotation
14 Cap 1 Cap on top of shaft that holds the shaft pieces together Cast, press fit together with shaft
15 N2 Link 2 1 31 Rubber around subassembly to allow for mounting Injection Molded
Retrieved from "http://wiki.ece.cmu.edu/ddl/index.php/Windshield_wipers"
Personal tools