Windshield wipers

From DDL Wiki

(Difference between revisions)
Jump to: navigation, search
Line 31: Line 31:
|-  
|-  
!   
!   
-
| ||colspan="2"|  RIGID SUBASSEMBLY  || || All pieces in this subassembly are still attached together and therefore do not have individual pictures.  We determined the components by observations ||  || [[Image:ww-rigid subassembly.jpg|100 px]]  
+
| ||colspan="2"|  RIGID SUBASSEMBLY  || || || All pieces in this subassembly are still attached together and therefore do not have individual pictures.  We determined the components by observations ||  || [[Image:ww-rigid subassembly.jpg|100 px]]  
|-  
|-  
! 9  
! 9  
Line 52: Line 52:
|-  
|-  
! 15
! 15
-
| colspan="3"|N2 Link 2 || 1 || 31 || Rubber around subassembly to allow for mounting || Injection Molded || [[Image:ww-rubber mount.jpg|100 px]]  
+
| colspan="3"|N2 Link 2 || 1 || 255 || Link which rotates both wipers with rubber connectors at each end || Cast with pressed on injection molded rubber connectors || [[Image:ww-link 2.jpg|100 px]]
-
 
+
|-
 +
! | colspan="3"|WIPER CONNECTION SUBASSEMBLY 2 ||  ||  ||  || || [[Image:wiper subassembly 2.jpg|100 px]]
 +
|-
 +
! 16
 +
|  || colspan="2"| Rubber cap || 1 || 0 || Rubber cap that goes over the wiper connection point in the subassembly || Injection molded, loose fit || [[Image:ww-rubber cap.jpg|100 px]]
 +
|-
 +
! 17
 +
|    ||colspan="2"|Hex Screws || 3 || 7 (#7+#8) || Screw to bolt wiper connection subassembly into car || Cast || [[Image:ww-hex screws.jpg|100 px]]
 +
|-
 +
! 18
 +
|  ||colspan="2"| Washers || 3 || 7 (#7+#8) || Washers to go with hex screws || Cast || [[Image:ww-washer.jpg|100 px]]
 +
|-
 +
! 19
 +
|  ||colspan="2"| Rubber thermal mount || 1 || 31 || Rubber around subassembly to allow for mounting || Injection Molded || [[Image:ww-rubber mount.jpg|100 px]]  
 +
|-
 +
! 
 +
| ||colspan="2"|  RIGID SUBASSEMBLY  || || || All pieces in this subassembly are still attached together and therefore do not have individual pictures.  We determined the components by observations ||  || [[Image:ww-rigid subassembly.jpg|100 px]]
 +
|-
 +
! 20
 +
| || || Straight Bar Link || 1 ||  || Connection to N2 Link 2, which causes the wipers to move || Cast, with the metal pin pressed in || 
 +
|-
 +
! 21
 +
| || ||Pin || 1 ||  || Pin that acts as the connection point to N2 Link 2 || Cast, pressed into 7L Link || 
 +
|-
 +
! 22
 +
| || ||Press Fit Ring || 1 ||  || Ring around the cylindrical shaft || Molded, press fit onto shaft || 
 +
|-
 +
! 23
 +
| || ||Washer || 1 ||  || Washer around shaft || Cast ||
 +
|-
 +
! 24
 +
| || ||Cylindrical Rings || 2 ||  || Two metal rings around the shaft of the assembly that allows for rotations, act like bearings || Cast, loose fit atop grease to allow for rotation || 
 +
|-
 +
! 25
 +
| || ||Cap || 1 ||  || Cap on top of shaft that holds the shaft pieces together || Cast, press fit together with shaft || 
 +
|-
 +
! 26
 +
| colspan="3"|Wiper Nut || 1 || 5 ||  || Cast || [[Image:ww-wiper nut.jpg|100 px]]
 +
|-
 +
! 
 +
| colspan="3"|WIPER ARM SUBASSEMBLY || 2  ||  || || ||
 +
|-
 +
! 27
 +
|  || colspan="2"| Hose || 1 || 5 || Rubber hose that transfers wiper fluid to the sprayer || Injection molded || [[Image:ww-rubber hose.jpg|100 px]]
 +
|-
 +
! 28
 +
|    ||colspan="2"|Nozzle || 1 || 2 || Nozzle that sprays wiper fluid on windshield || Injection Molded || [[Image:ww-nozzle.jpg|100 px]]
 +
|-
 +
! 30
 +
|  ||colspan="2"| Spring || 1 || 24 || Spring that keeps wipers pressed against windshield || Cast steel wound into spring shape || [[Image:ww-spring.jpg|100 px]]
 +
|-
 +
! 31
 +
|  ||colspan="2"| Spring Connector || 1 || 0 || Connector between the spring and the wiper arm || Cast || [[Image:ww-spring connector.jpg|100 px]]
 +
|-
 +
! 
 +
| ||colspan="2"|  WIPER ARM SKELETON SUBASSEMBLY  ||  || 255 || We could not detach these because the piece are riveted together and we wanted to preserve this piece|| || [[Image:ww-skeleton subassembly.jpg|100 px]]
 +
|-
 +
! 32
 +
| || || Link || 1 ||  || Connection to N2 Link 2, which causes the wipers to move || Cast, with the metal pin pressed in || 
 +
|-
 +
! 10
 +
| || ||Pin || 1 ||  || Pin that acts as the connection point to N2 Link 2 || Cast, pressed into 7L Link || 
 +
|-
 +
! 11
 +
| || ||Press Fit Ring || 1 ||  || Ring around the cylindrical shaft || Molded, press fit onto shaft || 
 +
|-
 +
! 12
 +
| || ||Washer || 1 ||  || Washer around shaft || Cast ||
 +
|-
 +
! 13
 +
| || ||Cylindrical Rings || 2 ||  || Two metal rings around the shaft of the assembly that allows for rotations, act like bearings || Cast, loose fit atop grease to allow for rotation || 
 +
|-
 +
! 14
 +
| || ||Cap || 1 ||  || Cap on top of shaft that holds the shaft pieces together || Cast, press fit together with shaft || 
 +
|-
|}
|}

Revision as of 14:20, 23 September 2007

Part # Part Name Quantity Weight (grams) Function Manufacturing Process Picture
1 Motor Connection Nut 1 6 Holds the entire wiper assembly to the motor Cast
2 Motor Connection Link (1L) 1 62 Link connecting the spinning motor to Link 1 Cast, with the knob pressed into it
3 Link 1 (LN3) 1 158 Cast, with the knobs pressed into it
4 Rubber Connections 2 Unable to detach Caps on Link 1 that are used to attach to the metal knobs in the connection links Injection molded and pressed onto the link
WIPER CONNECTION SUBASSEMBLY 1
5 Rubber cap 1 0 Rubber cap that goes over the wiper connection point in the subassembly Injection molded, loose fit
6 Hex Screws 3 7 (#7+#8) Screw to bolt wiper connection subassembly into car Cast
7 Washers 3 7 (#7+#8) Washers to go with hex screws Cast
8 Rubber thermal mount 1 31 Rubber around subassembly to allow for mounting Injection Molded
RIGID SUBASSEMBLY All pieces in this subassembly are still attached together and therefore do not have individual pictures. We determined the components by observations
9 7L Link 1 Connection to N2 Link 2, which causes the wipers to move Cast, with the metal pin pressed in
10 Pin 1 Pin that acts as the connection point to N2 Link 2 Cast, pressed into 7L Link
11 Press Fit Ring 1 Ring around the cylindrical shaft Molded, press fit onto shaft
12 Washer 1 Washer around shaft Cast
13 Cylindrical Rings 2 Two metal rings around the shaft of the assembly that allows for rotations, act like bearings Cast, loose fit atop grease to allow for rotation
14 Cap 1 Cap on top of shaft that holds the shaft pieces together Cast, press fit together with shaft
15 N2 Link 2 1 255 Link which rotates both wipers with rubber connectors at each end Cast with pressed on injection molded rubber connectors
colspan="3"|WIPER CONNECTION SUBASSEMBLY 2
16 Rubber cap 1 0 Rubber cap that goes over the wiper connection point in the subassembly Injection molded, loose fit
17 Hex Screws 3 7 (#7+#8) Screw to bolt wiper connection subassembly into car Cast
18 Washers 3 7 (#7+#8) Washers to go with hex screws Cast
19 Rubber thermal mount 1 31 Rubber around subassembly to allow for mounting Injection Molded
RIGID SUBASSEMBLY All pieces in this subassembly are still attached together and therefore do not have individual pictures. We determined the components by observations
20 Straight Bar Link 1 Connection to N2 Link 2, which causes the wipers to move Cast, with the metal pin pressed in
21 Pin 1 Pin that acts as the connection point to N2 Link 2 Cast, pressed into 7L Link
22 Press Fit Ring 1 Ring around the cylindrical shaft Molded, press fit onto shaft
23 Washer 1 Washer around shaft Cast
24 Cylindrical Rings 2 Two metal rings around the shaft of the assembly that allows for rotations, act like bearings Cast, loose fit atop grease to allow for rotation
25 Cap 1 Cap on top of shaft that holds the shaft pieces together Cast, press fit together with shaft
26 Wiper Nut 1 5 Cast
WIPER ARM SUBASSEMBLY 2
27 Hose 1 5 Rubber hose that transfers wiper fluid to the sprayer Injection molded
28 Nozzle 1 2 Nozzle that sprays wiper fluid on windshield Injection Molded
30 Spring 1 24 Spring that keeps wipers pressed against windshield Cast steel wound into spring shape
31 Spring Connector 1 0 Connector between the spring and the wiper arm Cast
WIPER ARM SKELETON SUBASSEMBLY 255 We could not detach these because the piece are riveted together and we wanted to preserve this piece Image:Ww-skeleton subassembly.jpg
32 Link 1 Connection to N2 Link 2, which causes the wipers to move Cast, with the metal pin pressed in
10 Pin 1 Pin that acts as the connection point to N2 Link 2 Cast, pressed into 7L Link
11 Press Fit Ring 1 Ring around the cylindrical shaft Molded, press fit onto shaft
12 Washer 1 Washer around shaft Cast
13 Cylindrical Rings 2 Two metal rings around the shaft of the assembly that allows for rotations, act like bearings Cast, loose fit atop grease to allow for rotation
14 Cap 1 Cap on top of shaft that holds the shaft pieces together Cast, press fit together with shaft
Retrieved from "http://wiki.ece.cmu.edu/ddl/index.php/Windshield_wipers"
Personal tools