From DDL Wiki

Executive Summary

Millions of wealthy skiers face difficulty walking in ski boots each year, generating a market for a convenient, inexpensive solution. An existing product manufactured by a now-defunct company, the original WalkEZ, provided some improvement to the step on flat surfaces. However, the device was rigid, and could not deform to provide additional support and dynamic response during the step. The device presented here is, in a nutshell, a new dynamic WalkEZ - a night and day improvement over the original. It uses various materials to provide a tuned spring-damper system during the step. MATLAB models and Finite Element Analysis guided development, and continuous user testing kept it grounded to reality. The result is a product beloved by its testers: it is lightweight, robust, and makes walking up and down stairs not a brush with death. These elements, identified as essential, are fulfilled nicely by the developed product. An initial production run of 60,000 at a market price of $40 is recommended.

Market Research

Fourteen skiers were approached during the market research. Of the group, eight were recreational skiers and six were members of the Carnegie Mellon Ski Team. We asked them for their opinions on walking in ski boots and where they wanted to see improvements. If they were aware of any existing solutions, we requested additional opinions on those solutions. Since most of the skiers that were approached had never heard of the Walk-EZ Revolutions, we had the skiers try them on. With minor adjustments, they were all able to fit into the walking attachment. Afterward, they gave us their feedback.

Survey

There was a general agreement that walking in ski boots is uncomfortable. Most of the recreational skiers wanted to see more flexibility in the boots, specifically around the ankles. Some of their responses were:

• “I just want to be able to bend at the ankles to get more mobility”
• “... the main issue is the flexibility of the foot. I don’t know if this would be possible, but maybe some mechanisms that allow the sole to bend for walking so you can bend your toes a bit.”
• “I would increase flexibility in the leg.”

Several of the serious skiers didn’t want any change on the boots that compromises the structural integrity of the boots and thus reducing the performance. By providing more flexibility to the boots, this provides less support for the ankles and thus jeopardizes the safety of the skier, especially when racing or moving quickly. Listed below were some experts' views on increasing the flexibility of the ski boot:

• “In my experience, there's not much you can do about it…there's always a trade off between comfort and performance.”
• “The other option is something like Tele-boots, which would have the movable toe built-in. I worry about a solution like that compromising boot response and stiffness though when in a binding along with insulation/leakage at the joint.”
• “I'd rather have a good experience skiing than a good experience walking around.”

The skiers agreed on the need of more flexibility around the ankles area when walking in ski boots, especially when walking up and down the stairs, but maintaining the rigidity to provide the support when skiing.

Existing Solutions

Several attempts at solving this problem have been made in the past. All of them have been unsatisfactory or have created more problems than they solve. The three most common solutions to this issue are unbuckling the clips on the boots, ski-walk adjustment, and the Walk-EZ Revolutions walking attachments.

Products

Products

The WalkEZ attachment.

Ankle-unlock lever (red) on ski boots.

Ankle-Unlock Lever

This adjustment allows the boot's upper cuff to hinge backward. This will give the skier the room needed for a more natural walking motion. Although this is a useful feature, most skiers would choose a more solid rear support in favor of walking comfort. Higher end boots will not have this feature for the reason that ski boots are not built to flex backward because the mechanism often causes the ski boot to lack a rearward support<ref>"Ski-Walk Adjustment." All-Mountain Skier. 2002. <http://books.google.com/books?pg=PA95&lpg=PA95&dq=ski+walk+adjustment&sig=429J6lcY8IXglXzEnxufU37W_f0&ct=result&id=U_w8rVNwCREC&ots=m4OD4WcT1B#PPA95,M1></ref>. All of the people who have tried this feature agree that this mechanism doesn't really work, as a few skiers claimed, "The lock/unlock mechanism doesn't really make very much of a difference because it doesn't provide a very significant degree of freedom" and "I always thought locking-unlocking things don't really improve anything." It provides inconsequential degree of freedom for walking, but the smallest change in the mobility of the boot while skiing dramatically affects the way one skis.

Walk-EZ Revolutions Walking Attachment

These are clip-on attachments for the soles of ski boots that provide a safe, gripping surface and have a curved form which allows a skier to walk more naturally. The addition of a simple, subtle curve to the bottom of the Walk-EZ allows the wearer to walk around in a natural, relaxed posture - eliminating the 15-degree angle/cant automatically imposed on your spine when in ski boots<ref>"Walk-EZ Revolutions" More Inspiration.<http://findarticles.com/p/articles/mi_qa3675/is_200705/ai_n19430501/pg_5></ref>. In addition, an ingenious double hinge allows the units to fold flat for easy storage when not attached to the bottom of the boot. Even though, this device transforms into something more compact, skiers would still rather deal with the discomfort of walking in ski boots than carrying two more things, as some skiers said, "I would love to use something like walk-ez, but I would hate to carry them while not in use, especially when you consider that you ski for several hours (in my case around 5 to 7 hours a day) and you walk for just 15-30 minutes a day" and "The down-side to this is that you have to put them on/take them off to walk in them. What if there were some kind of integrated flip-down version of this that stows away on the back of your boot or something. Might be a good start rather than lugging around extra gear in your camel-back." This was perhaps the best attempt in trying to solve the crisis in walking in ski boots.

Improvisations

Improvisations

Unbuckling boots is common and provides some improvement.

Wearing shoes until the last possible minute is a less common way of avoiding walking in ski boots.

Unbuckling the Boots

One way to walk easier in ski boots is to unbuckle the clips that fasten a skier’s foot to the boot. By unbuckling these clips, it allows a greater degree of freedom for the skier’s ankle to rotate because the shin is not held against the stiff outer shell that typically provides the support for the ankle. This outer shell protects the ankles and feet from injury while skiing but presents mostly comfort issues while walking. This practice however, becomes a hassle for inexperienced or young skiers. They would unlatch the clips to walk, and whenever they want to go back on the slopes, they would require assistance in buckling their boots back on. Although some people don't mind the hassle of unbuckling and buckling the clips, like one skier mentioned, "I find unbuckling the boots to work just fine and don't mind doing the John Wayne walk", generally speaking, this is a very inefficient way to acquire some comfort for just a simple task as walking.

Taking the Boots Off and Changing into Regular Shoes

The last existing solution to the discomfort of walking in ski boots is to simply take off the boots, store them somewhere relatively safe from being stolen, and put on regular pair of shoes. This solution is obviously the most time inefficient but also the most effective. In addition, this method risks the chance of having the pair of ski boots from being unlawfully taken when being left unattended unless you're willing to pay for a highly inflated locker space.

Expected Price and Production Volume

Because there are some variables in the actual production cost and manufacturing costs that we would really have trouble estimating, we'll give a very loose estimation of the cost of the device in the market. According to the materials used and based on the cost of the Walk EZ, we estimate that our product would cost between thirty and forty dollars. We came to this conclusion because the Walk EZ was only about twenty dollars and has a very similar production method. The primary difference is that we have some more expensive materials composing the sole, so we estimate that that might increase the production cost slightly. Of the thirty to forty dollars that the Walk EZ would cost the consumer, we've estimated that about fifteen to twenty dollars of it would go towards production costs.

Because the skiing market is so large, we have relatively lofty goals in terms of an initial production run. With 6 million skiers in the country and presumably all of them having trouble walking in their boots, there is a very large untapped market. If put into production, a very aggressive marketing campaign featuring endorsements from pro skiers and a lot of advertising in key locations would be required to get the product out to the masses. One of the key reasons for the failure of the Walk EZ is terrible marketing, something we would like to avoid repeating. So, with our all out marketing campaign, we believe that we might be able to reach one percent of the target market in our first year of production. With the number of skiers at 6 million, that makes our initial production run approximately 60,000 units. This production volume is enough to keep production costs low, but we are confident that the entire stock could be sold.

Based on our assumptions and ideal marketing scenario, the product is a pretty clear winner in terms in profitability. Much of the cost of the product is pure profit, since the production costs are relatively low. There is definitely enough of a promising outlook to justify further research and development of this product. We feel that there is a great potential for success in the market for a device like this, especially consider the favorable reactions we got at the design exposition. Virtually all skiers that heard our presentation said they would probably buy the device if it were on the market, and a few actually tried to buy our prototype. We are confident that with enough quality marketing, we could sell our initial production run and make this a very successful product.

Prototype Documentation

Prototype Testing

Following the completion of our third prototype, we spoke to seven guys (four are our own team members and three are from the ski team), and two girls (one is a fifty six year old mother and one is from the ski team). One ski boot was fitted with the WalkEZ and the other was fitted with the third prototype. All of which admitted to the improvement from the WalkEZ.

Prototype III

Prototype III: Top View.

Prototype III: Bottom View.

When the boots were fitted with the WalkEZ and the prototype III, the better product was apparent. The general consensus was that the third prototype performed significantly better in stairs than the WalkEZ. Some said:

• “Wow, I really can feel the deformation when I go up and down the stairs. I feel more supports, more grip, and safer on this thing.”
• “The bottom line is I feel more comfortable”
• "The WalkEZ still feels too stiff."

Even though the prototype was only 20% heavier, people agreed that they would prefer invest on our prototype rather than the WalkEZ. All of our testers responded extremely well to how the prototype III deformed as it did. The WalkEZ is made out of solid rubber, and hence, it is too stiff and does not take enough impulse from each step due to the lack of damping. Prototype III on the other hand, deformed enough to make the steps smoother, but stiff enough to provide the necessary supports.

User Testings: Observations of Deformations

Prototype III: Flat Ground.

Prototype III: Stairs.

Final Design vs. Prototype

Our final design is very similar to the prototype with the only differences coming mostly from refinement. In our prototype, we machined the top plate pieces from a sheet of polycarbonate. In addition, we screwed a piece of rubber onto the front for the toe piece. In our design, the top plate pieces would be injected molded from ABS, and the front top plate would have the toe piece incorporated into the piece. This difference would result in a weight reduction and a loss of a lot of the bulkiness of the device.

Another primary difference between the final design and the prototype is the hinging mechanism. In the final prototype, we simply screwed a door hinge onto the top plate. In our final design, the top plate has a series of notches carved out and a hole drilled from side to side inside the plate. A rod would be inserted into this hole and a series of links would go between the rods on the two pieces of the top plate. This mechanism would weight far less than the door hinge and would make it a lot more subtle contributing to the aesthetics and the size issue.

The sole would be mostly the same with only a few differences coming from better production methods. The pieces of foam, rubber, and silicon inside the sole would be stamped to have much greater precision than the hand cutting we did on the prototype. This difference would provide the final design version with much more robustness and a better feeling of stability. In addition to the differences in the inner workings of the sole, the grip piece would have treads carved into it similar to a boot or the original walk EZ. Because it was much too difficult for us to make a high quality tread and because we wanted to leave the inner sole exposed, we left the grip padding off of the prototype.

Design Documentation

Table 1: Bill of Materials

Assembly Number	Part Number	Name	Qty.	Function	Material	Manufacturing Process	Image	Engineering Drawing
1	N/A	Assembly, Main Body	1	Provides an area in which the boot rests and to create a shape that aids in walking and makes it a more natural motion	See individual Components	See individual Components	Error creating thumbnail: convert: unable to open image `/ux0/websites/wiki.ece.cmu.edu/wiki/virtual-hosts/ddl/images/SkiBoot_FinalDesign.jpg': No such file or directory @ error/blob.c/OpenBlob/2882. convert: no images defined `/ux0/websites/wiki.ece.cmu.edu/wiki/virtual-hosts/ddl/images/thumb/SkiBoot_FinalDesign.jpg/150px-SkiBoot_FinalDesign.jpg' @ error/convert.c/ConvertImageCommand/3235.	Error creating thumbnail: convert: unable to open image `/ux0/websites/wiki.ece.cmu.edu/wiki/virtual-hosts/ddl/images/SkiBoot_FinalDesign_Drawing.jpg': No such file or directory @ error/blob.c/OpenBlob/2882. convert: no images defined `/ux0/websites/wiki.ece.cmu.edu/wiki/virtual-hosts/ddl/images/thumb/SkiBoot_FinalDesign_Drawing.jpg/150px-SkiBoot_FinalDesign_Drawing.jpg' @ error/convert.c/ConvertImageCommand/3235.
	1	Front Frame	1	Provides the structural support of the front of walking attachment	ABS plastic	Injection Molded
	2	Rear Frame	1	Provides the structural support of the front of walking attachment	ABS Plastic	Injection Molded
	3	Silicone Strips	4	Provides the necessary components to the spring and dampener system	Silicone Rubber	Die Stamping
	4	Jet Black Rubber Strips	4	Provides the necessary components to the spring and dampener system	Medium Neoprene Rubber	Die Stamping
	5	Foam	2	Provides the necessary components to the spring and dampener system	Medium Natural Foam	Die Stamping
	6	Links	5	Attaches to the pins on both the front and back frame pieces so that the entire walking attachment can be folded in half	Aluminum	Die Stamping
	7	Pins	2	Creates an axis about which the links can rotate so that the entire walking attachment can be folded in half	Aluminum	Extruded and Cut		Not Applicable

There is no reason in redesigning a new clip assembly. The existing WalkEZ clip assembly works relatively well already. It is adjustable, robust, and cheap to make, and so our final design would contain a clip that's practically identical to the one on Walk EZ.

Assembly Number	Part Number	Image	Name	Qty	Weight	Function	Material	Manuf. Process
2	N/A		Assembly, Locking Mechanism	1	Sum of components	Clips down against the ski boot to lock the walking attachment in place, is a combination of assemblies 2a and 2b	See individual Components	See individual Components
2a	N/A		Assembly, Plastic Clip	1	Sum of components	Actually makes contact with the ski boot to hold walking attachment in place	See individual Components	See individual Components
	8		Clip, Large	1	23.2 g	Attaches to the Small Clip with the Clip Screw to create the Plastic Clip	Plastic	Injection Molding
	9		Clip, Small	1	6.9 g	Attaches to the Large Clip with the Clip Screw to create the Plastic Clip	Plastic	Injection Molding
	10		Clip Screw	1	1.6 g	Holds the Large and Small Clip pieces together to create Plastic Clip	Steel	Machining
2b	N/A		Assembly, Metal Frame	1	Sum of components	Attaches the plastic clip portion to the walking attachment main body and provides rigid support to keep the boot attached	See individual Components	See individual Components
	11		Spring	2	2.1 g	Allows the user to lengthen the entire Metal Frame in order to properly position the Plastic Clip to secure the ski boot	Steel	Winding
	12		Spring Retention Nut	2	0.7 g	Keeps spring within the Spring Containment Tube and allows it to be compressed, attaches to the Metal Frame End Piece	Steel	Machining
	13		Spring Containment Tube	2	5.1 g	Attaches to the Metal Frame Attachment and contains the Spring	Steel	Worked Tube Stock
	14		Metal Frame Attachment	2	2.6 g	Attaches to the Spring Containment tube and to the Pin to join the Main Body to the Locking Mechanism	Steel	Stamping
	15		Metal Frame End Piece	2	6.3 g	Attaches to the Metal Frame Arc using a Rivet and attaches to the Spring Retention Nut on the other end	Steel	Pressed Rod Stock
	16		Metal Frame Arc	1	13.6 g	Attaches on both sides to the Metal Frame End Pieces using a Rivet, also has the Plastic Clip attached to it	Steel	Pressed and Bent Rod Stock
	17		Clip Attachment	1	1 g	Attaches to the Metal Frame Arc and helps to hold the Plastic Clip in place	Steel	Worked Tube Stock
	18		Rivet	2	1.1 g	Attaches the Metal Frame End Piece to the Metal Frame Arc	Steel	Machining

Design Analysis

Failure Mode and Effects Analysis (FMEA)

Summary of Findings

The two most likely failure modes center around material wear during use (e.g. walking surface) and fatigue/overstrain (e.g. attachment spring). The walking surface, just like the sole of any other footwear, will inevitably wear with use. However, if the user possesses reasonable observational skills, this failure is detectable provided the user knows it is a problem. As for spring failure, the detectability of this failure is unfortunately quite high, as the user must notice the device's failure to lock onto the ski boot during installation. Other minor failure modes are mentioned, though they involve material choices and qualities - factors which require extensive analysis during the design phase but which are largely set once the product is released for manufacture. No failure mode mentioned below should present a large problem except for high-frequency usage.

Detailed Findings

How to read the table: The table below shows several ways in which the ski boot walking attachment may fail. The item and function column states the major components and their purposes, the possible failure mode column includes the possible ways in which the components may not perform as they are intended to, the effects of failure column describes the consequences of failure, the causes of failure column explains the possible sources of failure, and the design controls column explains methods in which the chance of failure mode can be reduced. The S,O, and D columns stand for severity, occurrence, and detection respectively. Severity is a measure of the significance of the effects of failure. Occurrence is a measure of the likelihood that a component will fail. Detection is a measure of the ability to detect the flaw either during the manufacturing process or by implementing the proposed methods mentioned in design controls. Finally, RPN stands for risk priority number, which is a quantification of design risk. RPN is the product of S, O, and D. The recommended actions column details proposed methods that can reduce the risk priority number. The responsibility column shows a group or an individual who would be responsible for the recommended action. The actions taken column explains actions that have been executed. Finally, the updated risk priority number due to the corrective action is displayed.

Any failures that jeopardize the functionality of the walking attachment and endanger the user would receive a severity score of an eight. For example, failures in connectors and pins would result in the walking attachment to be divided in half, which is inoperable at this point. If the failures occur while someone is walking, then he/she could very well be hurt. The smoothing of the rubber grips receive a seven because the system would still be operable, but it would no longer be safe to walk on especially on slippery surfaces like ice.

Occurrence and detection are typically rated very low (between two and three) because most of the components serve a simple purpose, contain almost no complexity in their geometry, and are visible without taking anything apart. Furthermore, the only components that would have a slightly more difficult time to notice when failing are the compression springs. Each spring is located inside a hollow cylindrical chamber that is part of the metal frame, but even if one spring fails fail, it would be noticeable because the metal the piece containing the spring would not be adjustable. The occurrence values are estimated by examining the material of each component, the purpose each component serves, and the complexity of its geometry. The scales that were used for rating the severity, occurrence of failure, and detection of failure can be found on page 708 and 709 of Engineering Design (Fourth Edition) by Dieter and Schmidt<ref>Dieter, George and Schmidt, Linda. "Engineering Design(Fourth Edition)." McGraw-Hill. NY, 2009.</ref>.

Design for X (DFX)

Design for X (DFX) analyzes a product to evaluate the efficiency of the product design from various perspectives. In this report, three major analyses are conducted on our final walking attachment design – Design for Manufacture (DFM), Design for Assembly (DFA), and Design for Environment (DFE). By conducting three types of DFX analyses, the overall efficiency of the product design during the manufacturing stage (DFM), assembly process (DFA), and post end-use impact to the environment (DFE) will be determined.

Design for Manufacture (DFM)

This design for manufacture analysis discusses how individual components of the walking attachment were designed in order to minimize the time and cost of the manufacturing process. The product design can be optimized for the manufacturing process through (1) reducing the number of components, (2) homogenizing the components, or (3) redesigning of the components. Reducing the number of components or homogenizing the components cuts the capital cost of production as fewer machines are required to manufacture the product. On the other hand, redesigning of the product aims to reduce the material cost per unit product by subtracting the unnecessary portions (dead weight) of the components from the original design. The following features of the final design contribute to the ease of manufacturing.

Symmetry

The walking attachment is identical for both the right and left boot. Because of this, the walking attachments can all be produced in the exact same way and they can simply be sold in pairs, without having to make sure there is one of each type in each pair. In addition to symmetry across the body, the walking attachment is, itself, symmetrical. If you cut the design down the middle from the front to back, it is a mirror image of itself. With this, the pieces of silicon and rubber on each side can be die stamped in the same way and that simplifies the manufacturing process.

Low Part Count

Because the final design contains very few parts, there are only a few manufacturing processes involved. We only need the rubber, silicon, and foam to be stamped, the entire top plate with toe piece can be made with two injection molding processes (one for the front and one for the rear), and the clip components, the links, and the folding rods can all be machined with relative ease. This is a pretty low number of manufacturing processes, and much of it can be done for a low price and in a small amount of time.

Easy Production

None of the processes listed above are incredibly time-consuming or costly and therefore manufacturing costs will remain relatively low. Each of the pieces production methods and advantages are listed below.

Top Plate

• The entire plate with toe piece can be made using injection molding allowing for a lightweight and robust design.
• Injection molding will waste little material and take a relatively low amount of time.
• Compared to other manufacturing processes, like machining, that could be used for this part, less material will be wasted, it will be faster, and at a higher production run, will cost less per unit.

Sole Components

• The sole components (the rubber, silicon, and foam) can all be die stamped.
• The production time will be very low.
• Although some material will be wasted, time saved and low input costs will keep the overall manufacturing costs low.

Clip Components

• The metal parts composing the clip can all be machined to specification with relative ease and little time.
• The metal pieces are all pretty simple, so machining will be easy and very few of them involve material removal.
• The plastic pieces on the clip can be made using injection molding.
• This allows for fast production and little material waste.

Design for Assembly (DFA)

A Design for Assembly analysis discusses how each component of the product was designed to minimize the time and cost of assembly. Efficient product design for assembly involves (1) simple configurations of the assembly and (2) ease of aligning the components. Simple configuration of the components prevents confusion and misplacement during the assembly process, while ease of aligning the components speeds up the assembly. The DFA on the main components of the walking attachment are provided below.

Sole

The sole is designed with a few pieces of rubber and foam embedded into two foam beds. All of these components are going to be die stamped, so the entirety of the assembly process will be arranging the pieces properly, and then gluing them together in the correct configuration. This must be done for the front and rear part of the sole. After these pieces are put together, the tread will be glued on to the bottom of the completed sole, and then the sole pieces themselves will be glued onto the front and rear top plates. Overall, the low number of parts and the simple arrangement were made for ease of assembly.

Top plate and Toe Piece

The top plate pieces themselves require no assembly since they each come as a single injection molded piece. In order to link the two halves together, the assembly worker must put the links in the appropriate slots, then slide the rods into the holes on the sides of the plate, and then simply cap the holes so the rod doesn't slide out. After that, the employee needs only to slide the rod through the rear plate, attach the clip to it, and then cap the ends. This linking design was made for very fast assembly because it only requires a few very easy steps.

Clip

The clip is by far the most complex part of the device for assembly. Although the assembly steps are somewhat difficult, there aren't that many parts so it doesn't take away from the overall low assembly time. The worker must take the large metal arc and rivet it to the connecting rod and then put the spring containment shell over the connecting rod. Once they put the spring inside, the cap needs to be attached to the end, and then the plastic clip itself needs to be screwed onto the metal arc. The clip is then completed and needs to be attached to the top plate to complete assembly of the device.

Design for Environment(DFE)

The design for environment analysis discusses how individual components of the walking attachment were designed in order to reduce the environmental impact of the product throughout its life-cycle. Design optimization of most products often puts more emphasis on DFM and DFA rather than on DFE, as reducing the time and cost of production would directly lead to greater profit. However, as environmental issues have come to draw more attentions from the public, the DFE analysis is becoming one of the significant aspects of product development that cannot be ignored.

Economic Input-Output Life Cycle Assessment (EIO-LCA) is often used as a common tool for conducting a DFE analysis on a product. EIO-LCA uses the following information as inputs - the product's purchase price and the most relevant sector to its manufacturing and end-usage. The EIO-LCA calculates how much environmental impact each of the manufacturing and the end-usage sectors creates from either producing or operating the amount of product(s) that is worth the input price of the simulation. The environmental impacts of the walking attachment calculated in this EIO-LCA include "Conventional Air Pollutants", "GHG Emission", and "Toxic Release".

Practically, a DFE analysis using EIO-LCA compares environmental impacts from the manufacturing sector and operational (end-usage) sector in order to assess which stage of the product's life cycle has the most significant impact on the environment. However, it is quite apparent that the walking attachment does not create any significant environmental impact during use since the product does not require any fuel to operate and is designed for long-term use (rather than being a quick, disposable product). Therefore, the environmental impact from end-usage of the walking attachment is said to be negligible. As a result, the main focus of this analysis is on the product's environmental impact during the manufacturing stage and its end of life (EOL) stage. The sectors associated with each of those stages are the "Sporting and athletic goods manufacturing" sector (manufacturing) and the "Waste management and remediation services" sector (EOL) respectively. The "US Department of Commerce 1997 Purchase Price Model" is used in all of the EIO-LCA presented in the following section since it is the most recently built model available that uses consumer purchase price as its input. The model makes estimation of "per-unit-product" environmental impacts easier as the market price of the product is known.

More emphasis on environment-friendly manufacturing methods

The detailed EIO-LCA results are summarized in the following section (Summaries and Specifics of EIO-LCA).

The simulation results show that manufacturing phase creates twice as much toxic release (30.1 kg/$1M) than disposal of the product does (15.1 kg/$1M). However, the relationship flips when discussing the amount of conventional pollutants emitted, as contributions from product disposal (2.5 metric tons/ $1M) nearly doubles that of manufacturing phase (1.3 metric tons/ $1M). What is more striking is that in terms of GHG emission, product disposal (7,600 MTCO2E/ $1M) has 10.5 times greater impact on the environment than the emission from the manufacturing sector (718 MTCO2E/ $1M). Thus, it is easy to conclude that in terms of environmental impact per cost, the most significant environmental impacts during the product's life cycle occurs in its post end-use (disposal) phase.

However, since the cost of manufacturing a unit of product and the cost of managing waste from a unit of product are not equal, environmental impact per unit of product (rather than per $1M economic input) needs to be determined. According to "THE PRICE OF SOLID WASTE MANAGEMENT SERVICES IN VERMONT" a study conducted by DSM Environmental Services, Inc. for the Vermont Department of Environmental Conservation (2005), managing 1 ton (1,000kg) of waste costs approximately $100. As the product analyzed in this DFE (WalkEZ) weighs about 1kg per unit, the waste management cost per unit is calculated to be around $0.10. The market price of the product is approximately $20 (200 times greater than the cost of waste management). Therefore, the simulated environmental impact per $1M from the EOL sector needs to be divided by a factor of 200 before being compared against the environmental impact per $1M from the manufacturing sector.

Combining those information, the manufacturing sector contributes approximately 0.602g of toxic release, 26.0g of conventional pollutants, and 0.0144 MTCO2E of GHG to the environment from producing one unit of the product. On the other hand, the EOL sector is responsible for 0.00151g of toxic release, 0.25g of conventional pollutants, and 0.00076MTCO2E of GHG per unit of product. Thus, it is apparent that the manufacturing sector is far more responsible for all the environmental impacts discussed here.

Major contributors to environmental impacts during the manufacturing phase

In manufacturing phase, power generation and supply are the biggest contributors to the sector's pollutants (77%) and GHG (29%) emissions. A more energy efficient manufacturing process would reduce those emissions.

More detailed results of EIO-LCA are summarized below.

EIO-LCA

• Model used:
  
  • US Department of Commerce 1997 Purchase Price
    
  • Walking Attachment Price ~ $20
    
    
• Manufacturing Sector:
  
  • Industry Group: Misc. Manufacturing
    
  • Industry Sector: #339920 - Sporting and athletic goods manufacturing
    
• End-use Sector:
  
  • Industry Group: N/A - Negligible environmental impact from operations of the product
    
• Post End-use (product after life) Sector:
  
  • Industry Group: Management, Administrative, and Waste Services
    
  • Industry Sector: #562000 - Waste management and remediation services
    
    

Comments on the industry sector selections
The manufacturing sector of the walking attachment is best represented by "Sporting and athletic goods manufacturing" sector. The example of the industries included in the sector include but are not limited to manufacturing of ski boots and various plastic athletic equipments. Given that the product is made of rubber materials (commonly used in several athletic equipments) and that the product's primary operation is for athletic/leisure purposes, "Sporting and athletic goods manufacturing" sector best describes the manufacturers of ski boot walking attachment - a very unique product.

EIO-LCA result displaying conventional pollutants per every $1M of product

Manufacturing Sector: Conventional Pollutants per every $1M of Product Manufactured

Post End-usage Sector: Conventional pollutants per every $1M of Product Disposed

EIO-LCA result displaying GHG emission per every $1M of product

Manufacturing Sector: GHG emission per every $1M of Product Manufactured

Post End-usage Sector: GHG emission per every $1M of Product Disposed

EIO-LCA result displaying Toxic Release per every $1M of product

Manufacturing Sector: Toxic Release per every $1M of Product Manufactured

Post End-usage Sector: Toxic Release per every $1M of Product Disposed

House of Quality

Diagram

Please click the House of Quality to display the full-resolution copy:

Conclusions

As calculated within the House of Quality, the two most important engineering aspects of the design are:

• Weight
• Spring-damping effect

Though this specific House of Quality reflects the final prototype, its very similar antecedent encouraged the team to focus on weight reduction during the design and fabrication of the final prototype. As discussed elsewhere in this report, the final prototype was 50% of the weight of Prototype II. This was achieved by conscious design decisions, such as the reorientation of the rubber-foam layers, and the change to soft foam to allow a smaller device height. As for the importance of the spring-damping effect, it serves as a good validation that this essential effect is proven to be essential by the House of Quality. The work put in to the MATLAB model during optimization of the layer structure was put exactly where it was needed: into refining the defining difference between this device and the original WalkEZ.

Mechanical Analysis

After collecting the feedbacks from users, who tested out the Prototype I, we concluded that the alternating layers of various rubber materials appear to improve a walking motion in ski boots. Therefore, the main goal of this "design memo" is to justify the use of alternating layers of different materials as opposed to using a large blocks of single material for walking attachment soles. The analyses consist of three major components - improvement of Matlab code, simple beam model analyses using manual calculations and FEA, and determination of effective spring stiffness of each rubber sample. Improvement of Matlab code will allow calculation of the optimal stress distribution on users' feet, while FEA would help establish the combination of rubber materials that yields the desired stress distribution. Finally, determination of spring stiffness of rubber materials is essential for manufacturing the optimal design calculated by the FEA. Since the access to Mechanical System Experimental Laboratory apparatus has not been available, the physical properties of rubber materials are yet to be determined; however, the simple beam analyses display that alternating layers of various spring elements is an effective method for achieving the desired stress distribution.

Simple Beam Model Analysis

Theoretical Model

Purpose of the Analysis

The primary goal of the simple beam model analyses using the theoretical model is to justify the use of layers of various rubber materials as an effective method of adjusting the net effective spring constant of specific region of the walking attachment.

Overview of Method

The theoretical model consists of several linear springs with various stiffness aligned in parallel. The theoretical model is prefered when predicting the static deformation of the walking attachment's soles. Under these simulations, only a vertical load is applied through the layers of rubber materials, and each segment of the sole can be treated as a linear spring.

The fundamental equation of the relationship between the displacement of linear springs in parallel and the external force being applied is listed below:

k_effective = k₁ + k₂ + ... k_n

The theoretical model is more reliable than Finite Element Analysis (FEA) when the analysis is simple and no tangential force is present. This is because the FEA requires setting the mesh size to an adequate level in order to obtain accurate results, and often times, stress concentration around sharp edges tends to approach infinity (which does not occur in reality). The theoretical model is simple, yet accurate enough for predicting the overall effective spring coefficient of the layers of rubber material as long as only vertical load is applied, and the deformation is reasonablly small. If friction force between the ground and the bottom of the walking attchment needs to be included in the analyses, the model will not satisfy the assumption that each segment of rubber material behaves as a linear spring due to the moment created by the tangential force. Also, when the significant amount of deformation occurs, behaviors of physical springs tend to diverge from that of ideal springs.

Following are the four simple models, whose net effective spring stiffness is calculated using the equation mentioned above. Each of those models are also designed and tested during the FEA (which is summarized in the next chapter). Images of those simulation models are available in the next chapter (Simple Beam Model Analyses - FEA) as well.

(1) To simulate the regions, where materials with high and low spring stiffness are altered, six layers of silicon (high stiffness material in this model) and five layers of rubber (low stiffness material in this model).

(2) To simulate the high stiffness region, a model that has silicon as all eleven of its spring elements was tested.

(3) To simulate the low stiffness region, a model that has rubber as all eleven of its spring elements was tested.

(4) To simulate the effect of varying the thickness of silicon layers and rubber layers, a model with Si-Si-Ru-Ru-Si-Ru-Si-Ru-Ru-Ru-Si combination was tested.

Assumptions and Boundary Conditions

• Treat each layer of rubber material as a linear spring element

• Only vertical load is being applied to the layers of rubber materials
  • As mentioned above, the theoretical model is accurate only when the rubber materials do not experience shear forces. Shear forces would cause spring elements' horizontal displacement, and rubber materials would no longer behave as linear spring elements.

• The user stands on a completely flat surface
  • Each spring element experiences the same amount of vertical deformation
  • This assumption is used just to simplyfy the analyses. If the deformation of the walking attachment's sole while the user walks on a slope needs to be determined in future analyses, it is likely that the FEA will be the primary method.

• The deformation of the spring element is small enough
  • If the vertical load compresses the rubber materials too far away from its equillibrium position, the physical springs' behaviors may diverge from that of ideal springs.

• Let the effective stiffness of each layer of rubber be 1N/mm and that of Si be 10N/mm
  • The spring coefficients of every rubber material will be obtained using MSE lab experiment apparatus.
  • For the time being, let the effective stiffness of the rubber be one tenth of the stiffness of Si to simplify the calculation.
  • In the next section (FEA), SolidWorks material properties (stored in the software's library) of rubber and Si are used to simulate the model.

Conclusions

The calculations yield the net spring stiffness of each model to be...

Model 1: 1.964 N/mm [Si-Ru-Si-Ru-Si-Ru-Si-Ru-Si-Ru-Si] Model 2: 10.000 N/mm [All Si] Model 3: 1.000 N/mm [All Rubber] Model 4: 1.692 N/mm [Si-Si-Ru-Ru-Si-Ru-Si-Ru-Ru-Ru-Si]

These calculation results will be compared against the results of FEA discussed in the next chapters. One thing to be noted is that teh calculation results from this theoretical model does not reflect any change in allocation of Si and Rubber layers. The net effective spring stiffness is only the function of the number of Si layers and number of Rubber layers that consist the model.

Finite Element Analyses (FEA) of a CAD (SolidWorks) model

1st model consists of alternating pattern of Si and Rubber layers.

2nd model consists of one large Si layer.

3rd model consists of one large Rubber layer.

4th model consists of Si-Si-Ru-Ru-Si-Ru-Si-Ru-Ru-Ru-Si combination.

Purpose of the Analysis

There are two primary goals of the simple beam model analyses using FEA.

(1) To justify use of layers of various rubber materials as an effective method of adjusting the effective spring constant of specific region of the walking attachment (just like the primary purpose of the theoretical model analyses).

(2) To determine the change in stress distributions as the combinations of rubber materials vary

Overview of Method

The SolidWorks model consists of a 10cm x 11cm base made of aclylic and eleven 10cm x 1cm x 5cm spring element layers made of various materials. Four combinations of spring elements were simulated to undergo 1cm of uniform compression in vertical direction while the base plate was being fixed.

(1) To simulate the regions, where materials with high and low spring stiffness are altered, six layers of silicon (high stiffness material in this model) and five layers of rubber (low stiffness material in this model).

(2) To simulate the high stiffness region, a model that has silicon as all eleven of its spring elements was tested.

(3) To simulate the low stiffness region, a model that has rubber as all eleven of its spring elements was tested.

(4) To simulate the effect of varying the thickness of silicon layers and rubber layers, a model with Si-Si-Ru-Ru-Si-Ru-Si-Ru-Ru-Ru-Si combination was tested.

Each model experiences uniform 1cm vertical compression while the base plate is "fixed." Both the displacement (deformation) and stress distributions plots are obtained from each simulation, and the net reaction forces in the vertical reaction (which is the force needed to cause the simulated deformation of spring elements) are also calculated.

Assumptions and Boundary Conditions

• Treat silicon layer as a high stiffness and rubber layer as a low stiffness spring element
  • Only two types of spring elements are used to simplify the analyses and focus on the effects of layer combinations and layer thickness on the effective stiffness of the entire model.

• Only vertical load is being applied to the layers of rubber materials
  • The primary goal of this analsis is "to justify the use of layers of various materials as an effective method for adjusting the effective spring stiffness."

• Each spring element experiences the same amount of vertical deformation (1cm)
  • If the load gets uniformly distributed over the bottom surface of the walking attachment, rubber layers (low stiffness spring elements) would deform more than silicon layers (high stiffness spring elements) do. In reality, however, the vertical force is applied on the spring elements via contact with the ground. Therefore, the deformation of the bottom surface (rather than the distribution of the load) needs to be uniform.

Conclusions

As predicted by much simpler theoretical models (in the previous chapter), displacement plots of simulations 1 and 4 display similar results. Also, the model 2 (All Si - high stiffness spring element) experiences much greater stress as its net effective spring stiffness is much greater than any other model, and to experience 1cm of vertical compression, much greater normal force (which linearly correlates to von Mises stress shown in the stress plot) needs to be applied.

The stress plots are also used to address the conclusion for the primary goal of this analysis - The use of alternating layers of various spring elements is an effective method for optimizing the walking attachment's design. As summarized in the stress plots of simulations 1 and 4, high stiffness spring elements (Si layers) experience much greater von Mises stress than low stiffness spring elements (Rubber layers) do. Thus, the FEA proves that using alternating layers of spring elements with various stiffness would effectively alter the stress distribution inside the sole of the walking attachment. Therefore, once the desired stress distribution experienced by user's feet is determined by the matlab simulation code, and the physical experiment results reveal spring stiffness per cross sectional area of each rubber material, the optimal design for the walking attachment can be calculated.

Model 1 Results: Alternating Layers

Simulation 1 Displacement.

Simulation 1 Stress.

Model 2 Results: All Silicon Layers

Simulation 2 Displacement.

Simulation 2 Stress.

Model 3 Results: All Rubber Layers

Simulation 3 Displacement.

Simulation 3 Stress.

Model 4 Results: Si-Si-Ru-Ru-Si-Ru-Si-Ru-Ru-Ru-Si

Simulation 4 Displacement.

Simulation 4 Stress.

Determination of Spring Constants and Damping Coefficients

Purpose of the Analysis

Rectilinear system used to test material properties.

Mount with material inside.

Mount and material taken apart with screw used to put material in mount.

The goal of this analysis was to obtain reasonably accurate spring constant and damping coefficient of each of the rubber materials being used for construction of the walking attachment. These experiments are essential for optimization of the walking attachment design since they would provide us with quantitative measures of the material properties as opposed to vague ideas of how well the materials act as springs and dampers. In addition, the material properties obtained in this experiment are crucial for beam model and MATLAB analyses in order for them to be more intuitive. Especially important is providing the MATLAB model with accurate data would help determine the optimal compositions of rubber and foam (neoprene, silicone, or natural rubber).

Overview of Method

In order to obtain the spring constant and damping coefficient of each material, the rectilinear experimental apparatus for the Mechanical Systems Experimentation (MSE) lab (24452) was used. This apparatus, as displayed in the first thumbnail on the right, consists of a motor, three carts, vertical supports, and three encoders. The motor applies inputs specified by the experimenters, the encoders measure the displacements, velocity, and acceleration of each cart. The carts can be connected to the vertical supports by springs or in this case, various rubber and foam samples. In order to determine the spring constant and damping coefficient, initial displacement from the equillibrium position can be applied manually, and the carts' response will be monitored. Using MATLAB code developed for the MSE labs, the logarithmic decrement method calculated the spring constants and damping coefficients.

With logarithmic decrement, the damping ratio is obtained with the following formula, where n = number of peaks used, x₁ = the displacement on the first peak, x_n = displacement on the nth peak, and zeta = damping ratio.

Using the damping ratio, we can obtain the natural frequency with the following formula, where T = period, omega = natural frequency, and the rest of the variables have the same definitions as above.

Using the natural frequency, we can find the spring constant using the following formula, where k = spring constant and the rest of the variables have the same definitions as above.

Using the damping ratio and spring constant, we can obtain the damping coefficient using the following formula, where b = damping coefficient, zeta = damping ratio, k = spring constant, and m = mass.

In addition to the initial displacement tests, applying a ramp input and dividing the input force by the displacement response over the course of the run could yield another measure for the material properties. With results from the two tests, reasonably accurate values of the spring constant and the damping coefficient can be obtained.

In order to attach the materials to the rectilinear apparatus, we had to specially design brackets to hold the materials and clamp on to the provided posts and carts. To do this, we used the system pictured in the bottom two thumbnails on the right. In the first picture, you can see the completed bracket with the material already screwed inside. The material is placed in the clamp-like area between the two pieces of acrylic. We then run screws through the acrylic, through the material, and out the other piece of acrylic to create a tight hold on the material. One piece of the acrylic is then attached to the stationary post on the rectilinear setup using the large screw sticking out of the back. The other piece of acrylic is mounted to the cart using the large screw. Since we couldn't find properly sized screws, we have implemented a couple nuts to hold the screw in the proper position.

Assumptions Made

In using the same kind of analysis we used in our MSE lab, we have assumed that the springs are linear. This may or may not be the case with the materials that we are testing. In order to correct for this, we will make sure to do each test a few times using different conditions. If the values match up pretty well, we can say that our assumption of a linear spring is valid. If the values don't match up well, our assumption is probably not valid, but it doesn't make the analysis completely pointless. Even if we can't get very exact values for the spring constant and damping coefficient, we still at least can get ballpark values, which is really what we want. Since no other tool of analysis we are using is especially accurate, we just need approximate spring constants and damping coefficients. In addition, a major purpose of this analysis is to acquire the spring constants and damping coefficients relative to each other. Whether or not the obtained values are particularly accurate is of minimal consequence.

Our assumptions also exclude the effects of friction, which there will obviously be. Again, since we are not looking for exact values for the material properties, this is of little consequence. As long as we obtain material properties on the right order of magnitude, The MATLAB model and the beam model analyses should be able to be conducted with a fair amount of accuracy. Since the other purpose of this analysis is to help us decide how to layer the sheets of rubber and foam, we only need relative values for.

Conclusions

One of the first tests we performed was that for testing spring linearity. We tested a couple of the materials by applying a ramped force. Since the response seemed to be following a linear path, we can assume that the materials behave like a linear spring.

After performing all of the tests, we obtained the following material properties, summarized in the chart below.

MATLAB Model

Note: full code may be found in the appendix

Purpose

The premise of the revised walking attachment is to improve comfort, control, and general walking ability. Intuition generated the first ideas regarding the chosen order of foam and rubber layers; the next step in the optimization is computer modeling. Using this MATLAB model, the ideal damping and spring amounts, locations, and zones can be determined by fitting the model output with the theoretical ideal step.

Assumptions

• Constant forward body velocity, and .6 seconds of foot contact per step
• Ideal hip motion is harmonic
• Expected hip motion is similar to the ski boot with no device attached
• Ankle is locked
• All deflection is one-dimensional, and normal to sole of foot
• All forces are exerted vertically
• Ideal spring-damping setup

Existing Model Data

Appendages included in simulation

Though it was obvious from simply wearing the ski boots that the step was changed, the specific change was not understood.

To address this lack of knowledge, a simulation was written in MATLAB to calculate foot, leg, and body motion during three step variations. A normal step is provided as a reference; the bare ski boot step demonstrates the roughness of the gait; and, finally, the efficacy of the WalkEZ is shown very clearly. The attachment eliminates the roughness created by the locking of the ankle, though the step is not restored to its original geometry.

The model employs kinesiologic research of joint motion in steps as described by Soutas-Little (cf references). For the normal gait, assumptions include standard footwear on an able person at a comfortable walking pace. To simulate a user wearing a ski boot, the ankle ankle is locked in the simulation, though other joint motion remains the same. Constant forward torso velocity is still assumed, and experimental results are consistent with this assumption. To simulate the WalkEZ, the entire leg is raised and lowered as the WalkEZ 'rolls' as it contacts the ground at the same angle as the foot. The simulation output is a diagram of limb position with respect to time. Joint motion data (as shown below) and with average limb lengths are the input, along with factors such as a locked ankle and the presence of a WalkEZ. Further customization is not implemented at this time, as the current level of control provides the desired function.

Cubic splines were fitted in MATLAB to provide continuous data for the simulations.

The results of this simulation are an analytical validation of the problem and current solution and are immediately useful as such. Additionally, future usefulness may be incalculable, as simulation of proposed designs will be possible with relevant additions to the code.

Normal Step

Hip height change during step.

Hip flex during step (torso-thigh angle)

Knee flex during step (thigh-shin angle)

Ankle flex during step (shin-foot angle)

Simulation of normal step motion

Simulation of step wearing ski boot

Simulation of step wearing ski boot and walking device

Effect of footwear selection upon Center of Mass change during stride. Note the attachment greatly smooths the change while the foot is bearing the body's weight.

As shown above, the device provides a significant improvement to the smoothness of the step, though it is only a partial solution. Further work is necessary to make the gait even more natural.

Method

The model uses time-stepping and binning to make calculations reasonable.

The analysis flows as such:

• A layer or layers of the device (for the first t, the heel) contacts the ground
• That layer(s) undergoes deformation until either:
  • the timestep is exceeded, upon which the current deflection is recorded and time is advanced, or
  • surrounding strip(s) make contact with the ground.
• The next timestep begins. Outputs from the previous timestep include deflection of each element, used now as the initial deflection.

The following diagram illustrates the two types of iteration:

Because of the approximation, simple differential equations can be solved in the time domain, since endpoints are known.

Endpoints include:

• Time - deflection can only occur for the duration of the timestep
• Distance - once the deflection equals the deflection of surrounding elements, those elements must be included

Graphically, the feedback can be seen as:

In Code

Full code is available here

Expected force is based on the acceleration of the body mass:

           f_expected = hip_dy2_dumb(i) * body_mass;

           w0 = (sum(k)/body_mass)^.5;
           gamma = sum(c)/(2*(sum(k)*body_mass)^.5);
           wd = w0*(1-gamma^2)^.5;
           compression_modifier(i) = stepsecs/wd*8200;
           %8200 is a constant determined iteratively to normalize compresisson_modifier
           dd(contact_indexes) = dd(contact_indexes) + ddstep(i)*compression_modifier(i);

           f_app_k = sum(k ./ body_mass .* dd(contact_indexes));
           f_app_c = f_expected - f_app_k;
           hip_dy_adj(i) = -f_app_c/sum(c/body_mass)/25400;

Outputs

The most important outputs are:

• Hip height
• Device y velocity, which is then subtracted from expected hip height to obtain
  • Adjusted height

which are then compared with the ideal motion as shown in the section above. The desired product will avoid any uncomfortable periods of high ground reaction force, yet will seek to keep the hip moving in its normal sinusoidal pattern.

Hip position is then shape-compared to the ideal body motion, which is the ultimate sign of how well the device functions.

Limitations

Though this model is designed to provide a good optimization method for hip motion, it may ignore the abstract idea of "control" as felt by the user. This group does not contain a kinesiologist, so further knowledge of user feelings is not on hand. We feel that user testing will be sufficient to lay to rest any concerns about control, and that same user testing will be useful for calibration of this MATLAB model as necessary.

Also, if the motion provided in the model is extreme, the assumption of constant forward body velocity may be invalid. Again, user testing may tell how large of an effect this has. However, we feel that since foam/rubber deformation will likely be minimal compared to the vertical displacement of the body center of mass, the assumption is a valid one for now.

Results

For reference, the motion of the foot and leg during the step appears as such:

The device velocity for six different spring-damper configurations:

The device displacement for six different spring-damper configurations:

Hip height reflecting the effect of the device in different configurations:

Conclusion

• Need high damping, high spring in middle of step to flatten it out
• Heel strike introduces high impact, so strong springs must be balanced by strong dampers
• Spring/damping not a huge concern during the last third of step, so save weight there
• Toe needs to be rather stiff, or be reshaped to a higher initial height

The contribution of the final design is:

As can be seen, it soaks up large bumps on heel strike, toe off, and in between when the full bodyweight is placed on the foot. There is no oscillation involved, meaning the damping is sound; user testing verified that the spring effects are strong enough to provide control during use.

Design Process

Process Overview

Most of the work on this project was done as a team. We did most of the construction together in the lab to make sure that everything was done correctly and so that everyone's ideas were involved in the production. It also helped to have everyone together to make the product so we could instantly verify whether or not ideas would work together.

The written work for this project was done on an individual basis with team collaboration for refinement, proof reading, and understanding. With the analysis, Brandon wrote his code and perfected it individually, Taka created the Solidworks model and ran the FEA studies on his own, and Randy and Jarrett worked together to test the materials and then run the analysis.

Contributors

Brandon

Randy

Taka

Jarrett

• Brandon Perry (Group Leader)
  • Executive Summary
  • House of Quality
  • Analysis: MATLAB Simulation
• Randyka Pudjoprawoto (Product/Market Specialist)
  • Market Analysis
  • Prototype Documentation
  • Analysis: Material Properties
• Taka Matsuura (Design Specialist)
  • Bill of Materials
  • CAD Model
  • Analysis: FEA
• Jarrett Valeri (Product/Design Specialist)
  • Analysis: Material Properties
  • DFX (DFM, DFA, DFE, EIO-LCA)
  • FMEA

Gantt Chart

Gantt Chart displaying the projected timeline for major tasks

As can be seen in our Gantt chart, we pretty evenly broke the project up across the semester and tried to do as much as possible in the appropriate time slot.

Next Steps

The next steps towards releasing this product to the market would probably be further refinement of the design to make it a little more streamlined and robust, and to perfect the finer points of the manufacturing processes. The foam and rubber layout is pretty accurate, so it probably doesn't need to be toyed with in the future, however, we would definitely need to work on the treading on the bottom of the attachment, and we would like to further develop the traction padding for use on ice.

In order to find success in the market place, the product would need an aggressive marketing campaign so that it could be discovered. We theorize that one of the main reasons that the Walk EZ flopped was its lack of marketing. We only knew about the Walk EZ because a group member is an avid skier and saw an ad for it in a skiing magazine. There are plenty of casual skiers that would buy this device, and I might go so far as to say that these casual skiers would actually be more likely to buy it. A lot of experiences skiers are used to walking in ski boots and have gotten used to the discomfort and danger. Someone who has never adjusted would be much more likely to buy our product, though word-of-mouth that danger is unnecessary would surely reel in a much wider swath of regular skiers.