Coffeemaker
From DDL Wiki
(Difference between revisions)
(→References) |
(→Product Introduction) |
||
Line 1: | Line 1: | ||
= Product Introduction = | = Product Introduction = | ||
+ | |||
+ | Product: Hamilton Beach 12-Cup Coffee Maker | ||
+ | |||
+ | [[Image:coffeemaker.jpg]] | ||
= Executive Summary = | = Executive Summary = |
Revision as of 04:29, 30 January 2014
Contents |
Product Introduction
Product: Hamilton Beach 12-Cup Coffee Maker
Executive Summary
Parts List
The following table is a list of all the parts that come out of the coffeemaker.
Bill of Materials
The following is a table of individual components, assemblies and certain off the shelf parts that we took apart during our dissection process of the coffeemaker.
Part Number | Name | QTY | Weight (g) | Function | Material | Manufacturing Process | Image |
---|---|---|---|---|---|---|---|
1 | Cubic Peg for Metal Strip | 1 | Holds the metal strip that goes around the glass container | Plastic | Injection Molding | ||
2 | Screw for the Glass Container | 1 | Tighten up the metal strip | Aluminum | Off Shelf Component | ||
3 | Lid for the Glass Container | 1 | Lid of the Glass Container | Plastic | Injection Molding | ||
4 | Metal Strip for the Glass Container | 1 | Goes around the glass container | Aluminum | Rolling and Machining | ||
5 | Handle for the Glass Container | 1 | Handle of the glass container | Plastic | Injection Molding | ||
6 | Filter Lever | 1 | Plastic | Injection Molding | |||
7 | Filter Spring | 1 | Aluminum | Off Shelf Component | |||
8 | White Filter Rubber Piece | 1 | Rubber | Injection Molding | |||
9 | Filter | 1 | |||||
10 | Plastic Lid | 1 | Plastic | Injection Molding | |||
11 | Cardboard Piece | 1 | Cardboard | Off Shelf Component | |||
12 | Bottom Screws | 5 | Aluminum | Off Shelf Component | |||
13 | Plastic Bottom Lid | 1 | Plastic | Injection Molding | |||
14 | Plastic Ring | 1 | Plastic | Injection Molding | |||
15 | Insulator Rubber Band | 1 | Rubber | Injection Molding | |||
16 | Heater Plate | 1 | |||||
17 | Heater Plate Screw | 1 | |||||
18 | Rectangular Lid Piece | 1 | |||||
19 | Rubber Tube Rings | 4 | Tighten and put the tubes in place | Copper | Machining | ||
20 | Heater Bar | 1 | Holds the heater in place | Aluminum | Extrusion and Machining | ||
21 | Heater | 1 | Heats both the water and the container | Aluminum | Casting | ||
22 | Resistor Piece | 1 | Part of the heater circuit | Assembly | Off Shelf Component | ||
23 | Little Screw for Plastic Wire Piece | 2 | Aluminum | Off Shelf Component | |||
24 | Slightly Larger Screw for Heater | 1 | Aluminum | Off Shelf Component | |||
25 | Nut for Heater Screw | 1 | Holds the Heater in Position | Aluminum | Off Shelf | ||
26 | Plastic Piece for Wires | 1 | |||||
27 | Smaller Screw | 5 | |||||
28 | Washer for Smaller Screw | 5 | |||||
29 | Top-Bottom Connection Screw | 3 | Connect the top and bottom half of the coffeemaker | Off Shelf Component | |||
30 | Lid Lever | 1 | Supports the lid | Plastic | Injection Molding | ||
31 | Plastic Volume Meter | 1 | Meter of the coffeemaker | Plastic | Injection Molding | ||
32 | Lid Hinge Connected to Tubes | 1 | Connection between the lid and tubes | Plastic | Injection Molding | ||
33 | Transparent Tube | 1 | Rubber | Injection molding | |||
34 | Opaque Tube | 2 | Rubber | Injection molding | |||
35 | Red Ball | 1 | Part of the valve in the opaque tube | Plastic | Injection Molding | ||
36 | Base of Switch | 1 | Base of the switch | Off Shelf Component | |||
37 | Switch | 1 | Control on/off of the coffeemaker | Plastic | Injection Molding | ||
38 | Tiny Spring | 1 | Part of the switch | Off Shelf Component | |||
39 | Tiny Piece from the Switch | 1 | Part of the switch | ||||
40 | Red Heating Connection | 2 | |||||
41 | Wires Coming out from the Heater | 2 | Rubber and Copper | Off Shelf Component | |||
42 | White Capacitor Screw | 2 | Put the capacitor in place | ||||
43 | Washer for Capacitor Screw | 2 | Washer for screw | Aluminum | Off Shelf Component | ||
44 | N label | 1 | Label negative of the circuit | plastic tape | Off Shelf Component | ||
45 | Switch with Three Wires | 1 | Inside part of the switch | Assembly | Off Shelf Component | ||
46 | Blue Wire | 1 | Off Shelf Component | ||||
47 | White Wire | 1 | Off Shelf Component | ||||
48 | Black Wire | 1 | Off Shelf Component | ||||
49 | Glass Container | 1 | Coffee Container | Glass | |||
50 | Top Part of Body | 1 | Top half of the coffeemaker | Plastic | Injection Molding | ||
51 | Bottom Part of Body | 1 | Bottom half of the coffeemaker | Plastic | Injection Molding |
Design For Manufacturing and Assembly (DFMA)
Failure Modes and Effects Analysis (FMEA)
Design for Environment (DFE)
Group 8 Team Members
Lucas Neffa
Andrew Vickory
Nick Ciesielski
Yang Wen
Kaifu Wang
References
1. Dieter, George E., and Linda C. Schmidt. Engineering Design. 4th Edition. New York, NY: McGraw-Hill, 2009. Print.
2. Hamilton Beach 12-Cup Coffee Maker, n.d. photograph, viewed 23 January 2014, <http://www.amazon.com/gp/product/B002EJF8TI/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1>