Motorcycle throttle lock
From DDL Wiki
Line 35: | Line 35: | ||
== Product Use == | == Product Use == | ||
- | Type 1 (cruiser) | + | '''Type 1 (cruiser)''' |
- | + | Operation | |
- | Operation | + | *The banjo bolt must be adjusted prior to use so that when the throttle lock is disengaged the throttle does not rub on the rubber ring, and when the lock is engaged the throttle sticks but can still be manually turned |
- | To Engage | + | To Engage |
+ | *While holding the throttle with the fingers and palm at the desired opening, press the thumb lever down into the engaged position. (The friction is such that the rider may still open and close the throttle. The throttle simply has a slight rotational stiffness.) | ||
- | To Disengage | + | To Disengage |
- | + | *while holding the throttle with the fingers and palm, press the oposite side of the thumb lever with the back of the thumb to place the throttle lock in the disengaged position. | |
- | Maintenance | + | Maintenance |
+ | *Remove periodically and check for rust or dirt build up. Clean pieces with brush and mild soap. Replacement parts may be required over time. | ||
+ | |||
+ | '''Type 2 (sport bike)''' | ||
+ | |||
+ | Operation | ||
+ | *The friction nut has a left hand thread. In readiness for engagement, it must be adjusted so that it makes light contact with the plastic thrust washer. | ||
+ | |||
+ | To Engage | ||
+ | *While rolling on the throttle, the friction nut can be gripped between the small finger and palm of the hand. This action tightens the nut and provides sufficient friction to set the throttle to the desired opening. (The friction is such that the rider may still open and close the throttle. The throttle simply has a slight rotational stiffness.) | ||
+ | |||
+ | To Disengage | ||
+ | *While rolling off the throttle, grip friction nut between small finger and palm of the hand. VERY IMPORTANT!! The throttle should open and snap close freely when correctly disengaged. | ||
+ | *Note: The Grub Screw is set to provide the necessary resistance on thread of friction nut. This may be adjusted periodically to take up wear. Use 2mm allen key. | ||
+ | |||
+ | Maintenance | ||
+ | *Remove kit annually. Unscrew friction nut and brush clean threads with mild soap. Apply petroleum jelly to threads and assemble. Adjust grub screw to desired operating resistance. Use the 2mm key. | ||
(O-Ring cushion: 19.6mm I.D. x 2.4mm section - if replacement is required) | (O-Ring cushion: 19.6mm I.D. x 2.4mm section - if replacement is required) | ||
Line 52: | Line 69: | ||
== Dissection procedure and exploded assembly == | == Dissection procedure and exploded assembly == | ||
[[Image:Team 8 exploded assembly full.JPG|right | 483x363px]] | [[Image:Team 8 exploded assembly full.JPG|right | 483x363px]] | ||
- | Dis-assembly procedure | + | '''Dis-assembly procedure for Type 1 Throttle Lock''' |
#Removing clamp | #Removing clamp | ||
#*take off clamp screw nut | #*take off clamp screw nut | ||
Line 71: | Line 88: | ||
#Cut out main body clamp set threads | #Cut out main body clamp set threads | ||
#*cut with hack saw | #*cut with hack saw | ||
+ | |||
+ | '''Dis-assembly procedure for Type 2 Throttle Lock''' | ||
+ | #Remove plastic thrust washer | ||
+ | #Unscrew left hand friction nut | ||
+ | #Remove O-Ring cushion with needle nose pliers | ||
== Mechanical Function == | == Mechanical Function == | ||
- | Type 1 (cruiser) | + | '''Type 1 (cruiser)''' |
This product is used to lock the throttle on a motorcycle. The usual way of riding a motorcycle requires the rider to hold the throttle on at all times to accelerate. This can lead to fatigue on long trips. This product uses a metal clamp with a plastic washer to hold the throttle in the on position while letting the rider relax his hand. There is a small spring and plastic switch for functionality and when the switch is turned off, it quickly allows the throttle to go to zero. | This product is used to lock the throttle on a motorcycle. The usual way of riding a motorcycle requires the rider to hold the throttle on at all times to accelerate. This can lead to fatigue on long trips. This product uses a metal clamp with a plastic washer to hold the throttle in the on position while letting the rider relax his hand. There is a small spring and plastic switch for functionality and when the switch is turned off, it quickly allows the throttle to go to zero. | ||
- | Type 2 (sport bike) | + | '''Type 2 (sport bike)''' |
This product serves the same purpose as the cruiser type throttle lock. This products different in how it accomplishes the task. The sport bike throttle lock is located on the outside of the throttle (directly to the right of one's right hand). It takes the place of the right hand end weight that sport bikes have. In order to "lock" the throttle the rider must turn the large nut on the throttle lock in the same direction as the accelerator. This will cause the nut to press against a washer which then presses against the motorcycle's throttle. The added friction from the washer being tightened by the left hand nut causes the throttle to be held in place. Unlike the cruiser style lock, this product does not have a "quick" release feature like some of its competing products. The user must manually tighten and loosen the throttle lock. It is possible to move the throttle while the throttle lock is engaged so long as it has not been over tighten. Although there is no quick release, this product is a very simple and effective cruise control for sport motorcycles. | This product serves the same purpose as the cruiser type throttle lock. This products different in how it accomplishes the task. The sport bike throttle lock is located on the outside of the throttle (directly to the right of one's right hand). It takes the place of the right hand end weight that sport bikes have. In order to "lock" the throttle the rider must turn the large nut on the throttle lock in the same direction as the accelerator. This will cause the nut to press against a washer which then presses against the motorcycle's throttle. The added friction from the washer being tightened by the left hand nut causes the throttle to be held in place. Unlike the cruiser style lock, this product does not have a "quick" release feature like some of its competing products. The user must manually tighten and loosen the throttle lock. It is possible to move the throttle while the throttle lock is engaged so long as it has not been over tighten. Although there is no quick release, this product is a very simple and effective cruise control for sport motorcycles. |
Revision as of 19:59, 3 February 2011
Contents |
Executive Summary
This is the executive summary.
Major Stakeholders and Product Needs
User
- easy to use
- safe
- easy to disengage
- durable
- attractive
- stays engaged over long distances and through vibrations
- intuitive to use
Installer
- easy to install and adjust for many different motorcycles
Retailer
- cheap
- attractive
- compact
Other motorists
- safe
- easy to disengage
Passenger
- safe
- reliable
- intuitive to use
Law enforcement
- Can failure lead to malfunction or an accident
Product Use
Type 1 (cruiser)
Operation
- The banjo bolt must be adjusted prior to use so that when the throttle lock is disengaged the throttle does not rub on the rubber ring, and when the lock is engaged the throttle sticks but can still be manually turned
To Engage
- While holding the throttle with the fingers and palm at the desired opening, press the thumb lever down into the engaged position. (The friction is such that the rider may still open and close the throttle. The throttle simply has a slight rotational stiffness.)
To Disengage
- while holding the throttle with the fingers and palm, press the oposite side of the thumb lever with the back of the thumb to place the throttle lock in the disengaged position.
Maintenance
- Remove periodically and check for rust or dirt build up. Clean pieces with brush and mild soap. Replacement parts may be required over time.
Type 2 (sport bike)
Operation
- The friction nut has a left hand thread. In readiness for engagement, it must be adjusted so that it makes light contact with the plastic thrust washer.
To Engage
- While rolling on the throttle, the friction nut can be gripped between the small finger and palm of the hand. This action tightens the nut and provides sufficient friction to set the throttle to the desired opening. (The friction is such that the rider may still open and close the throttle. The throttle simply has a slight rotational stiffness.)
To Disengage
- While rolling off the throttle, grip friction nut between small finger and palm of the hand. VERY IMPORTANT!! The throttle should open and snap close freely when correctly disengaged.
- Note: The Grub Screw is set to provide the necessary resistance on thread of friction nut. This may be adjusted periodically to take up wear. Use 2mm allen key.
Maintenance
- Remove kit annually. Unscrew friction nut and brush clean threads with mild soap. Apply petroleum jelly to threads and assemble. Adjust grub screw to desired operating resistance. Use the 2mm key.
(O-Ring cushion: 19.6mm I.D. x 2.4mm section - if replacement is required)
Reference: KAOKO Cruise Control Kits User and Safety manual that came with the product.
Dissection procedure and exploded assembly
Dis-assembly procedure for Type 1 Throttle Lock
- Removing clamp
- take off clamp screw nut
- remove washer and spring
- separate main assembly into two sub-assemblies
- throttle lock sub-assembly
- handle bar clamp sub-assembly
- Dis-assemble locking mechanism
- remove metal clamp
- remove clamp screws (3)
- Dis-assemble thumb lever
- remove axial screw
- Dis-assemble handle bar clamp
- remove screws (2)
- Analyze auxiliary parts
- rubber clamps
- wide throttle adapter with screw
- Cut out main body clamp set threads
- cut with hack saw
Dis-assembly procedure for Type 2 Throttle Lock
- Remove plastic thrust washer
- Unscrew left hand friction nut
- Remove O-Ring cushion with needle nose pliers
Mechanical Function
Type 1 (cruiser)
This product is used to lock the throttle on a motorcycle. The usual way of riding a motorcycle requires the rider to hold the throttle on at all times to accelerate. This can lead to fatigue on long trips. This product uses a metal clamp with a plastic washer to hold the throttle in the on position while letting the rider relax his hand. There is a small spring and plastic switch for functionality and when the switch is turned off, it quickly allows the throttle to go to zero.
Type 2 (sport bike)
This product serves the same purpose as the cruiser type throttle lock. This products different in how it accomplishes the task. The sport bike throttle lock is located on the outside of the throttle (directly to the right of one's right hand). It takes the place of the right hand end weight that sport bikes have. In order to "lock" the throttle the rider must turn the large nut on the throttle lock in the same direction as the accelerator. This will cause the nut to press against a washer which then presses against the motorcycle's throttle. The added friction from the washer being tightened by the left hand nut causes the throttle to be held in place. Unlike the cruiser style lock, this product does not have a "quick" release feature like some of its competing products. The user must manually tighten and loosen the throttle lock. It is possible to move the throttle while the throttle lock is engaged so long as it has not been over tighten. Although there is no quick release, this product is a very simple and effective cruise control for sport motorcycles.
Bill of Materials and Properties
DFMA
FMEA
DFE
Team Members and Roles
- Brandon VanTassel - Team Leader
- Matthew Doncheski - DFMA Lead
- Randall Oakes - FMEA Lead
- Nicholas Petrillo - DFE Lead