Sr. No.
| Part
| Function
| Number of parts
| Weight of 1 part (g)
| Material
| Manufacturing Process
| Standard Part
|
| | | | | | |
|
1 | Water Spout Assembly | | | | | |
|
a | Spout | Ejects pumped up water | 1 | 5 | Plastic | Injection Molding | No
|
b | Screw | Fastner | 2 | <1 | Steel | Purchased Part | Yes
|
c | Washer | Distribute load of fastner | 2 | <1 | Rubber | Purchased Part | Yes
|
| | | | | | |
|
2 | Bottom Assembly | | | | | |
|
a | Rubber Rest | Prevents shaking of the overall part | 6 | <1 | Rubber | Molding | No
|
b | Screw | Fastner | 8 | <1 | Steel | Purchased Part | Yes
|
c | Bottom Cover | Cover that comes off the bottom | 1 | 121 | Plastic | Injection Molding | No
|
d | Spring | Damp vibrations of the entire machine | 2 | <1 | Steel | | Yes
|
e | Sealant Gel | Prevents leakage of water | | <1 | | | Yes
|
| | | | | | |
|
3 | Rotary Bar Assembly | | | | | |
|
a | Plastic Bar | Rotates can/bottle once placed | 1 | 16 | Plastic | Injection Molding | No
|
b | Screw | Fastner | 2 | <1 | Steel | | Yes
|
c | Holder | Keeps bar in place | 1 | <1 | Plastic | Injection Molding | No
|
d | O rings | | 7 | <1 | Rubber | | No
|
| | | | | | |
|
4 | Circuiting - Electronics | | | | | |
|
a | Plastic Timer | Varies how long motor runs | 1 | 21 | Plastic | Injection Molding | No
|
b | Spring | | 1 | <1 | Steel | | Yes
|
c | Circuit Board | Contains the controlling | 1 | 43 | | Assembled | No
|
d | Screw | Fastner | 1 | <1 | Steel | | Yes
|
e | Metal Piece | | 1 | <1 | | Stamped Sheet Metal |
|
f | Limit Switch | Ensures that machine does not operate until lid is closed | 1 | 7 | | Assembled | No
|
| | | | | | |
|
5 | Lid Assembly | | | | | |
|
a | Lid | Covers the top of the product(must be shut to run) | 1 | 27 | Plastic | Injection Molding | No
|
b | Torsion Spring | Automatically opens the lid if not clicked in | 2 | <1 | Steel | | Yes
|
c | Screw | Fastner | 2 | <1 | Steel | | Yes
|
d | Plastic Casing | Forms a casing for the the torsional springs | 2 | <1 | Plastic | Injection Molding |
|
e | White Plastic Pieces | Hold Torsional Springs | 2 | 2 | Plastic | Injection Molding | No
|
f | Spring | | 2 | <1 | Steel | |
|
g | Button | Clicks when lid is shut | 1 | <1 | Plastic | Injection Molding | No
|
| | | | | | |
|
6 | Bottom Drain Assembly | | | | | |
|
| Drain | Water flows through from here to pump | | | Plastic | Injection Molding | No
|
a | Drain Cap | Prevents ice from entering | 1 | 4 | Plastic | Injection Molding | No
|
b | Screw | Fastner | 2 | <1 | Steel | | Yes
|
| | | | | | |
|
7 | Housing of the entire product | | 1 | 697 | Plastic | Injection Molding | No
|
| | | | | | |
|
8 | Motor Assembly | | | | | |
|
a | Motor | For pumping water and Running rotating bar | 1 | 173 | | Assembled | No
|
b | Drain Channel | Channels water towards the motor | 1 | 21 | Plastic | Injection Molding | No
|
c | Lower Housing | Houses Motor and provides passage for the flow of water | 1 | 14 | Plastic | Injection Molding | No
|
d | Middle Housing | | 1 | 44 | Plastic | Injection Molding | No
|
e | Upper Housing | | 1 | 17 | Plastic | Injection Molding | No
|
| | Connects drain channel to the L-shaped joint | | 13 | Rubber | Extrusion Molding | No
|
g | L-shaped joint | Connects the Drain Channel to the Rubber Tube | 1 | 9 | Plastic | Injection Molding | No
|
h | Circular Plate | Rotates Under Motor | 1 | 1 | Plastic | Injection Molding | No
|
i | Metal Holder | Metal Holder | 2 | 1.5 | | | No
|
j | Belt | Transfers rotational motion to the Shaft | 1 | <1 | Rubber | | No
|
k | Bevel Gear | Transfers rotational motion to the Belt | 1 | 8 | Plastic | Injection Molding | Yes
|
m | Screws | Fastner | 2 | <1 | Steel | | Yes
|
n | Washers | | 3 | <1 | Rubber | | Yes
|
o | Plastic Shaft | | 1 | 3 | Plastic | Injection Molding | No
|
p | Metal Shaft | | 1 | 2 | | | No
|