Cordless drill
From DDL Wiki
(Difference between revisions)
(→Product Dissection) |
(→Product Dissection) |
||
Line 23: | Line 23: | ||
| Supp. Handle Screw || 1 || Secure Support Handle | | Supp. Handle Screw || 1 || Secure Support Handle | ||
|- | |- | ||
- | ! | + | ! 004 |
- | | | + | | Nut || 1 || Secure Support Handle Screw |
|- | |- | ||
- | ! | + | ! 005 |
- | | | + | | Screw || 4 || Secure Case |
|- | |- | ||
- | ! | + | ! 006 |
- | | | + | | Screw || 1 || Secure Case |
|- | |- | ||
- | ! | + | ! 007 |
- | | | + | | Screw || 7 || Secure Case |
- | |- ! | + | |- |
- | | | + | ! 008 |
+ | | Casing Part || 1 || Hold in parts | ||
|- | |- | ||
- | ! | + | ! 009 |
- | | | + | | Casing Part || 1 || Hold in parts |
|- | |- | ||
- | ! | + | ! 010 |
- | | | + | | Strap || 1 || useless |
|- | |- | ||
- | ! | + | ! 011 |
- | | | + | | Plastic Plate || 1 || Provide drill information |
|- | |- | ||
- | ! | + | ! 012 |
- | | | + | | Large Case R || 1 || Hold in parts |
|- | |- | ||
- | ! | + | ! 013 |
- | | | + | | Large Case L || 1 || Hold in parts |
|- | |- | ||
- | ! | + | ! 014 |
- | | | + | | Clutch Trigger || 1 || Move clutch |
|- | |- | ||
- | ! | + | ! 015 |
- | | | + | | Screw || 3 || Hold motor to chuck |
|- | |- | ||
- | ! | + | ! 016 |
- | | | + | | Motor || 1 || provide torque |
|- | |- | ||
! Row header 1 | ! Row header 1 |
Revision as of 00:38, 31 January 2007
Contents |
Cordless Drill
Group II Ming Huo Scott Miller Vishesh Nandedkar Mark Rockwell
Product Dissection
Before doing anything else, we dissected our drill to take a look at each part up close and understand how the drill works from a technical standpoint.
Part | Description | Qty | Function |
---|---|---|---|
001 | Battery | 1 | Provide electricity |
002 | Support Handle | 1 | Provide support for non-dominant hand |
003 | Supp. Handle Screw | 1 | Secure Support Handle |
004 | Nut | 1 | Secure Support Handle Screw |
005 | Screw | 4 | Secure Case |
006 | Screw | 1 | Secure Case |
007 | Screw | 7 | Secure Case |
008 | Casing Part | 1 | Hold in parts |
009 | Casing Part | 1 | Hold in parts |
010 | Strap | 1 | useless |
011 | Plastic Plate | 1 | Provide drill information |
012 | Large Case R | 1 | Hold in parts |
013 | Large Case L | 1 | Hold in parts |
014 | Clutch Trigger | 1 | Move clutch |
015 | Screw | 3 | Hold motor to chuck |
016 | Motor | 1 | provide torque |
Row header 1 | cell 1,1 | cell 1,2 | |
Row header 1 | cell 1,1 | cell 1,2 | |
Row header 1 | cell 1,1 | cell 1,2 | |
Row header 1 | cell 1,1 | cell 1,2 | |
Row header 1 | cell 1,1 | cell 1,2 | |
Row header 1 | cell 1,1 | cell 1,2 | |
Row header 1 | cell 1,1 | cell 1,2 | |
Row header 1 | cell 1,1 | cell 1,2 | |
Row header 1 | cell 1,1 | cell 1,2 |
Function/Purpose:
Spin "bits" with a specified torque (variable stepping torque)
- many different types of "bits"
- Drive screws
- Drill holes
- removing stripped bits
- Mixing paint/batter/dough
- pumping water w/ drill powered pump
- impromptu dremeling
- binding things
- home construction
- alignment
- safety
Inputs/Outputs:
- INPUTS: Axial force
- INPUTS: Trigger Pull
- INPUTS: Electricity (battery)
- INPUTS: Countertorque (resist what motor implements)
- OUTPUTS: Rotational motion
- OUTPUTS: torque
Use and Basic operation:
(scenario where putting screw in wall)
- Charge Battery
- Remove battery from charger
- Slide battery into drill
- Select bit/tool
- Loosen Chuck
- insert bit and tighten chuck
- select "cut-off" torque
- engage drive or gear
- Place head of screw on bit.
- Hold head of screw to bit (with hand).
- Place Tip of screw to desired object
- Partially squeeze trigger to provide low rotation-speed at first. All this while pushing axially.
- once screw's thread catch the wood, pull trigger to increase torque/omega.
- consistantly adjust to make sure bit is in line with screw.
- Let go of trigger when screw at desired location.
Different Users / Use Scenarios
- weak wrist/grip
- shaky hands
- can't push hard enough
- tightening Chuck
- Actual drilling into material
- Dead battery
- Improper/Hard surface
- Screw stripping
- Screw alignment
- Wrong bits.
- Aligning bit correctly within chuck
- Poor eyesight
- Poor hand-eye cooridnation
- Over-torquing (too soft a surface)
- Poor lighting
- no hands
- tight areas/corners (awkward shape)
- Hard time hearing maybe can't hear what's happening
- screw stripping
- overtorqueing
- not strong enought to switch between F/N/R