From DDL Wiki

Revision as of 21:34, 21 September 2008

Executive Summary

For the past three weeks, team 11 has been analyzing the Wheely King RC car made by Hobby Products International. Our research is done in order to improve on the current design and make the car significantly better at Rock Crawling. Rock Crawling is an upcoming sport, and our group feels that with the Wheely Kings transformation into a Rock Crawler, a significant profit can be made.

The Wheely King is a 1/12 replica, having many intricate parts, and while having most of the weight in the rear, the car is designed to raise up on its two rear wheels. After analyzing the gears, a ratio of 23:1 was calculated, showing that the car is initially designed for more acceleration than torque and a below average top speed (18 mph). Through DFMA analysis and DFX analysis we found..........*****Zahoor, write a little sentence or two here, say that we found many parts that could be produced as one. Keep in mind that you are talking to an executive, so do not get too technical....... Through these findings, many design changes are possible to make the car perform to the consumers desired needs. Here is our list of recommendations:

Manufacture ..(Ricci, enter 2 or 3 parts here)... out of metal instead of plastic. The stronger parts will make the product more durable and capable of withstanding large torques.

Reduce the gear ratio to increase the amount of torque the car produces. Increasing the size of the pinion gear does not require any new parts other than the gear its self and can reduce the gear ratio to 10:1. This will dramatically improve the performance of the car. High torque is essential in rock crawling, so overlooking acceleration and top speed is justified.

Zahoor...... put your input on the dfx stuff here. I.e. if you make these 5 parts into 1, it will save lots of money.....

Stakeholder/Customer Needs

There are a few stakeholders that need to be considered when designing and manufacturing a Nitro RC car. First, raw material users in the company that provide the parts made of plastics, metal and rubber. The design of the parts should not be too complicated that injection molds are adequate for the scale of part. If parts are small, it may be difficult to make an accurate mold of an important small part. With design for manufacturing in mind as well, there should not be too many different parts to be molded making it easier on component producers. Next in mind are those who assemble the cars. The design of the RC car must be easy because there are many parts. The parts cannot be too hard to assemble together because of positioning or the size or placement of necessary fasteners. Again, similar parts are important for assemblers because it may be hard to distinguish very similar parts in assembly that may make a big difference if assembled to wrong way. Finally, the end product is important to the customers who buy the RC car. Since we are considering an off-road RC car, the product has to be durable through a significant lifespan. The car has to be built for off-road rock crawling and tricky terrain. The car also needs to be easy to fix, modify or replace parts if broken.

Product Use and Function

Our particular product is a 4x4 remote control truck Wheeley King. It is an entry car for those interested in off road RC. The car is used and designed to crawls rocks and scale inclines with tricky terrain. These cars are not built for speed. They should be built to be durable because of the tough terrain it will be used on and should be durable for novice operator who are not as skilled and may damage the car easily. RC cars need to be built to be easily modified for improvement if someone chooses to improve the performance of their car.

The RC car runs off of a rechargeable battery. The battery supplies a Sturn motor. The motor is geared down to provide more torque to the tires so that the motor can handle the tough forces that an off-road RC car may encounter. Power is distributed to front and rear wheels, making the car 4 wheel drive. Differentials located on front and rear axles allow for powered turns and more power supply to a slipping wheel. The car is designed with a wide wheel base to guard against rolling. The wheel base also twists and has shocks to adapt to rough terrain to allow for reasonable traction on many types of uneven surfaces.

Parts Table

Notes:

Masses omitted for non-vehicle components (i.e. radio transmitter, battery charger, included tools, etc.)

Design for Manufacturing and Assembly

Failure Modes and Effects Analysis

Design for Environment (DFE)

Total for all sectors 646. 555. 57.4 20.6 12.8

|325211||Plastics material and resin manufacturing||29.4||29.4||0||0||0 |- |562000||Waste management and remediation services||23.6||3.73||19.9||0.029||0 |- |211000||Oil and gas extraction||20.7||3.47||17.2||0||0 |- |325190||Other basic organic chemical manufacturing||18.1||12.4||0||5.64||0 |- |324110||Petroleum refineries||14.2||14.1|.079||0||0|| |- |331111||Iron and steel mills||13.5||13.5||0||0||0

	Sector	GWP MTCO2E	CO2 MTCO2E	CH4 MTCO2E	N2O MTCO2E	CFCs MTCO2E
221100	Power generation and supply	205	203	0	0	2.47
484000	Truck transportation	49.0	48.3	0.075	0.674	0
3221A0	Paper and paperboard mills	48.7	48.7	0	0	0
339930	Doll, toy, and game manufacturing	35.3	35.3	0	0	0
325211	Plastics material and resin manufacturing	29.4	29.4	0	0	0
562000	Waste management and remediation services	23.6	3.73	19.9	0.029	0
211000	Oil and gas extraction	20.7	3.47	17.2	0	0
325190	Other basic organic chemical manufacturing	18.1	12.4	0	5.64	0
324110	Petroleum refineries	14.2	.079	0	0
331111	Iron and steel mills	13.5	13.5	0	0	0

Mechanical Analysis

Process

describe your team process for coordinating and completing all tasks

Retrieved from "https://wiki.ece.cmu.edu/ddl/index.php/RC_rock_crawler_truck"