Remote control tarantula
From DDL Wiki
(Difference between revisions)
(→Components:) |
(→Components:) |
||
Line 53: | Line 53: | ||
* Takes torque of motor, drives the front axle | * Takes torque of motor, drives the front axle | ||
* Off-center axle hole | * Off-center axle hole | ||
- | || Plastic || Injection Molded, smoothed || | + | || Plastic || Injection Molded, smoothed || [[Image: RC_Tarantula_Part_010.jpg |100px]] |
|- | |- | ||
| 011 || Driving Wheel 2 || 1 || | | 011 || Driving Wheel 2 || 1 || | ||
* Shares axle with Driving wheel 1 | * Shares axle with Driving wheel 1 | ||
* Off-center axle hole | * Off-center axle hole | ||
- | || Plastic || Injection Molded, smoothed || | + | || Plastic || Injection Molded, smoothed || [[Image: RC_Tarantula_Part_011.jpg |100px]] |
|- | |- | ||
| 012 || Plastic Protection housing || 1 || | | 012 || Plastic Protection housing || 1 || | ||
* Holds motor and gearing in place on interior of robot | * Holds motor and gearing in place on interior of robot | ||
* Provides internal support for robot | * Provides internal support for robot | ||
- | || Plastic || Injection Molded || | + | || Plastic || Injection Molded || [[Image: RC_Tarantula_Part_012.jpg |100px]] |
|- | |- | ||
| 013 || Back Wheel Axle || 2 || | | 013 || Back Wheel Axle || 2 || | ||
* Each axle has a Back wheel fitted on it, allows back wheels to roll | * Each axle has a Back wheel fitted on it, allows back wheels to roll | ||
- | || Steel || Cut wire, smoothed || | + | || Steel || Cut wire, smoothed || [[Image: RC_Tarantula_Part_013.jpg |100px]] |
|- | |- | ||
| 014 || Battery Cover Washer || 1 || | | 014 || Battery Cover Washer || 1 || | ||
Line 127: | Line 127: | ||
* Motor that powers tarantula | * Motor that powers tarantula | ||
* Worm-geared output shaft | * Worm-geared output shaft | ||
- | || Metal wiring, magnets, Metal casing, plastic gearing || Assembly || | + | || Metal wiring, magnets, Metal casing, plastic gearing || Assembly || [[Image: RC_Tarantula_Part_027.jpg |100px]] |
|- | |- | ||
| 028 || Circuit Board Assembly || 1 || | | 028 || Circuit Board Assembly || 1 || | ||
Line 133: | Line 133: | ||
* has attached antenna | * has attached antenna | ||
* controls motor function | * controls motor function | ||
- | || Circuit Board (silicon), metal wires || Assembly || | + | || Circuit Board (silicon), metal wires || Assembly || [[Image: RC_Tarantula_Part_028.jpg |100px]] |
|- | |- | ||
| 029 || LED Assembly || 1 || | | 029 || LED Assembly || 1 || | ||
* Aesthetic assembly to make eyes of tarantula glow as it moves | * Aesthetic assembly to make eyes of tarantula glow as it moves | ||
- | || Circuit (silicon), metal wires, LED || Assembly || | + | || Circuit (silicon), metal wires, LED || Assembly || [[Image: RC_Tarantula_Part_029.jpg |100px]] |
|- | |- | ||
| 030 || Tarantula exterior bottom || 1 || | | 030 || Tarantula exterior bottom || 1 || | ||
* outer shell of tarantula | * outer shell of tarantula | ||
- | || Plastic || Injection Molded, hand modified || | + | || Plastic || Injection Molded, hand modified || [[Image: RC_Tarantula_Part_030.jpg |100px]] |
|- | |- | ||
| 031 || Tarantula exterior top || 1 || | | 031 || Tarantula exterior top || 1 || | ||
* outer shell of tarantula | * outer shell of tarantula | ||
* covered in fake "fur" | * covered in fake "fur" | ||
- | || Plastic || Injection Molded, hand modified || | + | || Plastic || Injection Molded, hand modified || [[Image: RC_Tarantula_Part_031.jpg |100px]] |
|- | |- | ||
| 032 || Battery Connector || 1 || | | 032 || Battery Connector || 1 || | ||
* Small flat metal piece that connects + end of one battery to - end of the other | * Small flat metal piece that connects + end of one battery to - end of the other | ||
- | || Steel || Cut sheet metal || | + | || Steel || Cut sheet metal || [[Image: RC_Tarantula_Part_032.jpg |100px]] |
|- | |- | ||
| 033 || Battery + connector || 1 || | | 033 || Battery + connector || 1 || | ||
* connects to + end of batteries in series, connects to wire which runs to motor | * connects to + end of batteries in series, connects to wire which runs to motor | ||
- | || Steel || Cut sheet metal || | + | || Steel || Cut sheet metal || [[Image: RC_Tarantula_Part_033.jpg |100px]] |
|- | |- | ||
| 034 || Battery - connector || 1 || | | 034 || Battery - connector || 1 || | ||
* connects to - end of batteries in series, connects to wire which runs to motor | * connects to - end of batteries in series, connects to wire which runs to motor | ||
- | || Steel || Cut sheet metal || | + | || Steel || Cut sheet metal || [[Image: RC_Tarantula_Part_034.jpg |100px]] |
|- | |- | ||
| 035 || Metal screw receiver || 1 || | | 035 || Metal screw receiver || 1 || | ||
* threaded cylinder of steel to receive a screw | * threaded cylinder of steel to receive a screw | ||
* mounted inside bottom plastic exterior to stop screw from tearing into plastic | * mounted inside bottom plastic exterior to stop screw from tearing into plastic | ||
- | || Steel || threaded cylinder || | + | || Steel || threaded cylinder || [[Image: RC_Tarantula_Part_035.jpg |100px]] |
|- | |- | ||
|} | |} |
Revision as of 10:57, 21 September 2007
Contents |
Executive summary
Customer needs
Function
Product use
Components:
Part # | Part name | QTY | Function | Materials | Manufacturing Process | Picture |
---|---|---|---|---|---|---|
001 | Cover Screws | 13 |
| Steel | Cold headed, Thread Rolled | |
002 | Inner Flat-headed screw | 2 |
| Steel | Cold headed, Thread rolled | |
003 | Battery Cover | 1 |
| Plastic | Injection Molded, hand modified | |
004 | Back Wheel housing | 1 |
| Plastic | Injection Molded | |
005 | Back Wheel | 2 |
| Plastic | Injection Molded, smoothed | |
006 | Small Leg | 4 |
| Plastic | Injection Molded | |
007 | Medium Leg | 2 |
| Plastic | Injection Molded | |
008 | Large leg | 2 |
| Plastic | Injection Molded | |
009 | Feelers | 2 |
| Plastic | Injection Molded | |
010 | Driving Wheel 1 | 1 |
| Plastic | Injection Molded, smoothed | |
011 | Driving Wheel 2 | 1 |
| Plastic | Injection Molded, smoothed | |
012 | Plastic Protection housing | 1 |
| Plastic | Injection Molded | |
013 | Back Wheel Axle | 2 |
| Steel | Cut wire, smoothed | Image:RC Tarantula Part 013.jpg |
014 | Battery Cover Washer | 1 |
| Plastic | Punched | |
015 | Gear 1 | 2 |
| Plastic | Injection Molded | |
016 | Gear 2 | 1 |
| Plastic | Injection Molded | |
017 | Gear 3 | 2 |
| Plastic | Injection Molded | |
018 | Gear 4 | 1 |
| Plastic | Injection Molded | |
019 | Axle 1 | 1 |
| Steel | Cut wire, smoothed | |
020 | Axle 2 | 1 |
| Steel | Cut wire, smoothed | |
021 | Axle 3 | 1 |
| Steel | Cut wire, smoothed | |
022 | Axle 4 | 1 |
| Steel | Cut wire, smoothed, stamped rough areas | |
023 | Axle 5 | 1 |
| Steel | Cut wire, smoothed, stamped rough areas | |
024 | Axle Cap | 1 |
| Plastic | Injection Molded | |
025 | Switch Assembly | 1 |
| Circuit Board (silicon), metal wires, plastic switch | Assembly | |
026 | Switch Cover | 1 |
| Plastic | Injection Molded | |
027 | Motor Assembly | 1 |
| Metal wiring, magnets, Metal casing, plastic gearing | Assembly | |
028 | Circuit Board Assembly | 1 |
| Circuit Board (silicon), metal wires | Assembly | |
029 | LED Assembly | 1 |
| Circuit (silicon), metal wires, LED | Assembly | |
030 | Tarantula exterior bottom | 1 |
| Plastic | Injection Molded, hand modified | |
031 | Tarantula exterior top | 1 |
| Plastic | Injection Molded, hand modified | |
032 | Battery Connector | 1 |
| Steel | Cut sheet metal | Image:RC Tarantula Part 032.jpg |
033 | Battery + connector | 1 |
| Steel | Cut sheet metal | Image:RC Tarantula Part 033.jpg |
034 | Battery - connector | 1 |
| Steel | Cut sheet metal | Image:RC Tarantula Part 034.jpg |
035 | Metal screw receiver | 1 |
| Steel | threaded cylinder | Image:RC Tarantula Part 035.jpg |