Soda gun
From DDL Wiki
(Difference between revisions)
(→Bill of Materials) |
(→Bill of Materials) |
||
Line 324: | Line 324: | ||
|Paper | |Paper | ||
|Printed | |Printed | ||
+ | | | ||
+ | |- | ||
+ | Part Number | ||
+ | |Name | ||
+ | |Qty | ||
+ | |Weight (g) | ||
+ | |Function | ||
+ | |Material | ||
+ | |Manufacturing Process | ||
+ | |Image | ||
+ | |- | ||
+ | |- | ||
+ | |1 | ||
+ | |Plastic Regulator Backing | ||
+ | |1 | ||
+ | |41 | ||
+ | |Hold tubes to regulator | ||
+ | |P | ||
+ | |Injection Molded | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |2 | ||
+ | |"flat top, 1"" len, 1/4"" dia, philips head screw" | ||
+ | |4 | ||
+ | |3 (ea) | ||
+ | |Fastens regulator casing together | ||
+ | |SS | ||
+ | |Std Purchase Part | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |3 | ||
+ | |Tube retainer, retaining clips | ||
+ | |20 | ||
+ | |<1 | ||
+ | |Retain the tube retainers to base | ||
+ | |SS | ||
+ | |Std Purchase Part ?? | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |4 | ||
+ | |Property of Pepsi sticker | ||
+ | |2 | ||
+ | |<1 | ||
+ | |Identifies Pepsi product | ||
+ | |Paper | ||
+ | |Printed | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |5 | ||
+ | |Tube housing, main body | ||
+ | |1 | ||
+ | |46 | ||
+ | |Holds the tube housing | ||
+ | |P | ||
+ | |Injection Molded | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |6 | ||
+ | |Tube housing, single holder | ||
+ | |10 | ||
+ | |6 | ||
+ | |Connects two sides of tubes | ||
+ | |P | ||
+ | |Injection Molded | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |7 | ||
+ | |Shut-off screw | ||
+ | |10 | ||
+ | |<1 | ||
+ | |Shuts off soda flow | ||
+ | |P | ||
+ | |Injection Molded | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |8 | ||
+ | |"Shut-off screw o-ring 1/4"" dia, rubber" | ||
+ | |10 | ||
+ | |<1 | ||
+ | |Seals shut-off screws | ||
+ | |Rubber | ||
+ | |Std. Purchase Part | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |9 | ||
+ | |Flow adjustment screw | ||
+ | |10 | ||
+ | |<1 | ||
+ | |Adjusts syrup/water ratio | ||
+ | |P | ||
+ | |Injection Molded | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |10 | ||
+ | |"Flow adjustment screw o-ring, 1/4"" dia, rubber" | ||
+ | |10 | ||
+ | |<1 | ||
+ | |Seals adjustment screw | ||
+ | |Rubber | ||
+ | |Std. Purchase Part | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |11 | ||
+ | |"Housing retaining pin 1"", 5/32"" dia" | ||
+ | |2 | ||
+ | |4 | ||
+ | |Holds tube housing halves together | ||
+ | |SS | ||
+ | |Cut to length | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |12 | ||
+ | |Pivot pin for separating mechanism | ||
+ | |1 | ||
+ | |<1 | ||
+ | |Creates pivot point for half separator of plastic reg. housing | ||
+ | |SS | ||
+ | |Cut to length | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |13 | ||
+ | |Plastic regulator fronting | ||
+ | |1 | ||
+ | |63 | ||
+ | |Hold tubes to regulator | ||
+ | |P | ||
+ | |Injection Molded | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |14 | ||
+ | |Cap of separating mechanism, white | ||
+ | |1 | ||
+ | |<1 | ||
+ | |User interaction point for separator mechanism | ||
+ | |P | ||
+ | |Injection Molded | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |15 | ||
+ | |Cap of separating mechanism rivot | ||
+ | |1 | ||
+ | |<1 | ||
+ | |Held cap to main separating body | ||
+ | |SS | ||
+ | |Turned/Lathed | ||
+ | | | ||
+ | |- | ||
+ | |- | ||
+ | |16 | ||
+ | |Main separator body | ||
+ | |1 | ||
+ | |5 | ||
+ | |Separates the halves | ||
+ | |P | ||
+ | |Injection Molded | ||
| | | | ||
|- | |- |
Revision as of 19:05, 30 January 2014
Executive Summary
Bill of Materials
Part # | Part Name | QTY | Weight (g) | Function | Manufacturing | Material | Image |
---|---|---|---|---|---|---|---|
Soda Gun Sub-Assembly | |||||||
1 | "Round head 1/2"" Length 1/8th"" Dia Phillips" | 2 | <1 | Fastens button panel | SS | Std Purchase Part | |
2 | Elliptical Soda Button (Top) | 2 | <1 | User input button for soda, designates type | P | Injection Molded | |
3 | Eliptical Soda Button (Bot) | 2 | <1 | Translates input key foce to release soda | P | Injection Molded | |
4 | Circle Soda Button (Top) | 8 | <1 | User input button for soda, designates type | P | Injection Molded | |
5 | Circle Soda Button (Bot) | 8 | <1 | Translates input key foce to release soda | P | Injection Molded | |
6 | "Flat head 3/8"" len 1/8"" dia philips" | 2 | <1 | Fastens panel to gun body | SS | Std Purchase Part | |
7 | Plastic Washer (For Part #6) | 2 | <1 | Spacing | P | Injection Molded | |
8 | Small Butterfly Cliip | 2 | <1 | Aligns button to pin valves | SS | Die Cast, punched | |
9 | Large Butterfly Clip | 2 | <1 | Aligns button to pin valves | SS | Die Cast, punched | |
10 | Button Panel, blue, 10 button | 1 | 12 | Holds all buttons in place | P | Injection Molded | |
11 | "Round head 1"" len 1/8"" dia flat screw" | 2 | <1 | Fastened gun to hose base | SS | Std Purchase Part | |
12 | "Round head 1/2"" len, 1/8"" dia flat screw" | 2 | <1 | Fastened gun to hose base | SS | Std Purchase Part | |
13 | "Hexagon, 7/8"" len, 1/8"" dia threaded head (Recieves Part #11)" | 2 | <1 | Fastened gun to hose base | SS | Std Purchase Part | |
14 | Nozzle caps, clear plastic | 10 | <1 | Reduces hose diameter into gun base | P | Injection Molded | |
15 | O-ring, rubber | 10 | <1 | Seals hose to gun base | Rubber | Std Purchase Part | |
16 | "Round head, 3/8"" len, 1/8"" dia, philips screw" | 5 | <1 | Fasten back panel to gun | SS | Std Purchase Part | |
17 | Back panel, blue | 1 | 6 | Provides grip to back of gun, aesthetic | P | Injection Molded | |
18 | "Custom screw, 1/2"" len, 1/8"" dia, flat head" | 1 | <1 | Supports back panel | SS | Std Purchase Part | |
19 | Rubber o-ring for Part #18 | 1 | <1 | Seals screw, provides snug fit | Rubber | Std Purchase Part | |
20 | "O-ring, rubber, red 1/4"" dia" | 12 | <1 | Seals valve assy | Rubber | Std Purchase Part | |
21 | Clear plastic spring cap | 12 | <1 | Caps spring (Part #22) | P | ||
22 | "Small spring, 1/2"" len" | 12 | <1 | Translates input to opening valve, reset valv when released | SS | Std Purchase Part | |
23 | "O-ring, rubber, red, 1/8"" dia" | 12 | <1 | Seals (Part #24) to valve assy | Rubber | Std Purchase Part | |
24 | Pin | 12 | <1 | Holds valve in place, allows for vertical motion | SS | Std Purchase Part | |
25 | Plastic valve | 12 | <1 | Glued to pin, opens/closes each syrup line | P | Injection Molded | |
26 | Soda gun Nozzle, plastic, blue | 1 | 13 | Focuses final soda dispense | P | Injection Molded | |
27 | "Black, O-ring, rubber, 1"" dia" | 1 | <1 | Seals nozzle head to gun | Rubber | Std Purchase Part | |
28 | Soda gun body | 1 | 113 | Directs and organizes flow for all fluids exiting soda gun | P | Machined in five layers, irreversibly sealed together, post-drilled | |
29 | Soda gun nozzle base | 1 | 10 | Creates central location for syrup+soda to mix and exit gun | P | Turned, glued to soda gun body | |
30 | Soda gun nozzle base retaining pins | 2 | <1 | Create fixture points for nozzle base | SS | Turned | |
31 | Stickers (misc.) | 12 | <1 | Provides information and instructions about product, barcodes, safety information use, and beverage types | Paper | Printed | |
Name | Qty | Weight (g) | Function | Material | Manufacturing Process | Image | |
1 | Plastic Regulator Backing | 1 | 41 | Hold tubes to regulator | P | Injection Molded | |
2 | "flat top, 1"" len, 1/4"" dia, philips head screw" | 4 | 3 (ea) | Fastens regulator casing together | SS | Std Purchase Part | |
3 | Tube retainer, retaining clips | 20 | <1 | Retain the tube retainers to base | SS | Std Purchase Part ?? | |
4 | Property of Pepsi sticker | 2 | <1 | Identifies Pepsi product | Paper | Printed | |
5 | Tube housing, main body | 1 | 46 | Holds the tube housing | P | Injection Molded | |
6 | Tube housing, single holder | 10 | 6 | Connects two sides of tubes | P | Injection Molded | |
7 | Shut-off screw | 10 | <1 | Shuts off soda flow | P | Injection Molded | |
8 | "Shut-off screw o-ring 1/4"" dia, rubber" | 10 | <1 | Seals shut-off screws | Rubber | Std. Purchase Part | |
9 | Flow adjustment screw | 10 | <1 | Adjusts syrup/water ratio | P | Injection Molded | |
10 | "Flow adjustment screw o-ring, 1/4"" dia, rubber" | 10 | <1 | Seals adjustment screw | Rubber | Std. Purchase Part | |
11 | "Housing retaining pin 1"", 5/32"" dia" | 2 | 4 | Holds tube housing halves together | SS | Cut to length | |
12 | Pivot pin for separating mechanism | 1 | <1 | Creates pivot point for half separator of plastic reg. housing | SS | Cut to length | |
13 | Plastic regulator fronting | 1 | 63 | Hold tubes to regulator | P | Injection Molded | |
14 | Cap of separating mechanism, white | 1 | <1 | User interaction point for separator mechanism | P | Injection Molded | |
15 | Cap of separating mechanism rivot | 1 | <1 | Held cap to main separating body | SS | Turned/Lathed | |
16 | Main separator body | 1 | 5 | Separates the halves | P | Injection Molded |