Search results

From DDL Wiki

For more information about searching DDL Wiki, see Help.

Showing below up to 20 results starting with #21.

View (previous 20) (next 20) (20 | 50 | 100 | 250 | 500)

Page text matches

• Tie rack assembly
  ... ot stripped and the plastic is not stressed. We concluded this because the screws show no evidence of stripping and the plastic is not damaged in any way. 12.Screw the Magnetic motor (018) into place using two Screws (005).
  4 KB (701 words) - 00:22, 26 February 2007
• Automatic can opener redesign
  ... batteries need changing. A drop of silicone gel would be placed over the screws, magnet, and cutting wheel. Rubber gasket hoods would also be place over ... * Quick Snaps would eliminate the screws and easier for alignement
  44 KB (7495 words) - 04:04, 7 May 2007
• Active climbing cam, 1st report
  ... Most of the parts used in this assembly do not have any external fasteners/screws; this reduces the assembly time considerably. Some parts however require ...
  27 KB (4359 words) - 23:47, 4 March 2007
• Staple Gun Survey6
  | screws
  705 B (92 words) - 17:05, 16 March 2007
• Tie rack components
  | 002 || Locking screws || 2 || Lock Top assembly into place over closet rod || - || 12 || Cap: 2. ... | 005 || Screws || 6+7+2 ||
  6 KB (717 words) - 20:56, 7 March 2007
• Ceiling-mounted bicycle lift structural analysis
  There is a total of 8 ceiling screws responsible for holding the 50 pound load. To calculate the holding capac ...
  9 KB (1306 words) - 04:42, 20 March 2007
• Ceiling-mounted storage lift FMEA
  | rowspan=4 | Wood Screws
  4 KB (470 words) - 14:59, 9 May 2007
• Ceiling-mounted storage lift
  ... e band saw, drilled holes into the ends for screws, added springs to these screws and placed them on the upper bracket so that they were spring loaded.
  29 KB (4904 words) - 14:57, 9 May 2007
• Storage Lift Consumer Assembly
  ... e confirmed, attach the ceiling mount(2) to the ceiling by drilling 4 wood screws(3) through the holes shown below. ... ime as shown below and attach the middle to the ceiling by drilling 2 wood screws(3) through each of the channel mounts(4).
  4 KB (564 words) - 23:20, 6 May 2007
• Babyproof door knob lock
  | screws x2 || outer doorknob || 0.1 || brass plated || cold heading, thread woolin ... ... knob rose || outer doorknob || 3.0 || steel || molded and tapped || houses screws and connects inner doorknob to outer doorknob || [[Image:doorknob_part38.j ...
  27 KB (4047 words) - 05:26, 12 October 2007
• Remote control tarantula
  | 001 || Cover Screws || 13 || ... a melted piece of plastic. This was most likely put in place to keep metal screws from ripping apart the softer plastic shell, but the work done to keep thi ...
  34 KB (5056 words) - 16:51, 12 October 2007
• Airsoft gun
  | Screws for Cheek Rest Assembly | Screws for Low Ammunition Indicator Cover
  44 KB (6527 words) - 19:38, 12 October 2007
• Ice cream maker
  ... re to design the gear box base as one piece or to use fasteners instead of screws to assemble the base together. | Removed all four rubber stoppers [021] and removed screws that were underneath || [[Image:IC Step 1.JPG]]
  36 KB (5842 words) - 08:39, 10 December 2007
• Bilge pump
  | 3 || Screws || 2 || **Tools could also be eliminated if fasteners such as screws and rivets were eliminated
  28 KB (4426 words) - 03:53, 9 October 2007
• Windshield wipers
  ... ew to bolt wiper connection subassembly into car || Cast || [[Image:ww-hex screws.jpg|100 px]] | ||colspan="2"| Washers || 3 || 7 (#7+#8) || Washers to go with hex screws || Cast || [[Image:ww-washer.jpg|100 px]]
  8 KB (967 words) - 21:49, 23 September 2007
• Windshield wiper assembly
  ... t wiper connection subassembly into car || Steel || Cast || [[Image:ww-hex screws.jpg|100 px]] | ||colspan="2"| Washers || 3 || Washers to go with hex screws || Steel || Cast || [[Image:ww-washer.jpg|100 px]]
  37 KB (5779 words) - 01:56, 5 December 2007
• Vacuum cleaner
  ... Holds cover on motor assembly || Turned || Steel || [[Image:dirtdevilsmallscrews.jpg|100px]] ... ces many vibrations. These vibrations can lead to eventual losening of the screws. The use of snaps would eliminate the potential for this problem.
  23 KB (3452 words) - 20:07, 12 October 2007
• Blender
  ... motor to motor cover || Aluminum || Extrusion/rolled || [[Image:motorcoverscrews.JPG|150px]] ... cover and motor assembly. || Aluminum || Extrusion/rolled || [[Image:basescrews.JPG|150px]]
  33 KB (5152 words) - 20:44, 12 October 2007
• Paintball gun
  ... the head. Although a Phillips head screw would quicken assembly, Phillips screws are prone to stripping, leaving the end-user with a marker that is impossi ... ... ese two can be joined downstream in the production order by a pair of long screws.
  36 KB (5596 words) - 21:21, 12 October 2007
• Ratcheting screwdriver
  ... asymmetrical. Also in both tools, several pieces were held together with screws. In both cases, these can be replaced with snap fasteners to cut down the ... A ratcheting screwdriver is used for loosening and tightening screws. First, the user has to choose the correct bit type and size. All bits ha ...
  29 KB (4620 words) - 19:44, 12 October 2007

View (previous 20) (next 20) (20 | 50 | 100 | 250 | 500)