Retractable umbrella

From DDL Wiki

Revision as of 14:14, 23 September 2012

Figure 1. Totes Umbrella

Executive Summary

Major Stakeholders and Their Needs

Four major stakeholders were identified in the life cycle of the umbrella: the consumer, the retailer, the manufacturer and the distributor. Each of them is described in detail in the following subsections.

Consumer

An umbrella is a product commonly used by people to refuge from rain and other environmental phenomena. Most people have had at least one umbrella in their lifetime, therefore consumer diversity was considered during the evaluation of their needs. The requirements of the consumer can be summarized as:

• Rigidity: the product needs to be able to support itself in the hands of the person using it.

• Portability: consumers want a product that they can carry around all day, they need a product that is compact and easy to carry.

• Appearance: the products should appeal the consumer.

• Low cost: as a product that users carry all day, umbrellas tend to be lost or forgotten often. A low cost device could be replaced more often, than an expensive one. In addition, many consumers would not want to spend a large amount of money in a commonly used object.

• Safety: umbrellas have many small components and outstanding elements, they need to be safe for people to use.

• Durability: consumers want a product that does not need replacement often

• Light-weight: commonly, consumers carry umbrellas all day with them, most would opt not to carry or use it if it is too heavy.

Retailer

The fact that umbrellas are commonly used object makes their market a competitive one. Retailers needs are focused on making their product profitable. The following list summarizes their needs:

• Appearance: the product needs to be appealing to the consumer to be competitive .

• Price: the product needs to have a reasonable price that will yield revenue.

• Reliability: the product needs to be reliable, since its reputation reflect on the name of the retailer.

• Safety: the product needs to be safe, since the retailer is responsible for accidents that an error in the product could cause.

Manufacturer

Manufacturers want to minimize the cost and time of manufacturing processes. The following list summarizes their needs:

• Simplicity of the design: manufacturers need a simple design with simple geometries

• Modularity of the design: manufacturers need a modular design that optimizes the processes of manufacture.

• Materials: low cost and non-toxic materials minimize the cost of the manufacture.

• Manufacturing process: low cost

• Storage: minimum the weight and overall dimensions make the object easier to store and transport.

Distributor

Distributors want to minimize the cost and time of distribution of the product. The following list summarizes their needs:

• Compact: the product needs to be easy to pack and able to survive distribution

• Modularity: the product needs to have modular replacement parts

• Storage: minimum the weight and overall dimensions make the object easier to store and transport.

Product History

Product Functionality and Use

To open the umbrella, the user presses the button on the handle and allows it to extend and then expand fully. Then he or she holds the umbrella over her or his head, so as to prevent the elements from reaching her or him. To close the umbrella, the user pulls the rider down until it is locked back into the handle.

Mechanical Function

Figure 2. Cross-Section of Telescoping Mechanism & Handle

Figure 3. Cross-Section of Umbrella Arm

Bill of Materials

Assembly List

Figure 3. Exploded View of Umbrella

Figure 4. Exploded View of Handle

Figure 5. Exploded View of Canopy

Parts List

Part Number	Name	Quantity	Mass, g	Function	Material	Manufacturing Process	Image
01	Elastic Rope	1	3	Provides a convenient mode of carrying the umbrella when not in use	Rubber + Polyester	Cut from source rope and tied into loop shape
02	Rope Clip	1	< 1	Clips over tied end of elastic rope handle (part #01) to prevent fraying. Also the sight of brand logo	Plastic	Injection Molding
03	Handle Mechanism Casing	1	38	To house release mechanism. Added weight and rigidity of clear cylindrical block enhances stability and strength	Plastic	Injection Molding
04	Screw	1	< 1	Attaches handle casing (03) to the anchor (05) and to the telescoping shaft (08)	Steel	Subtraction & Deformation
05	Anchor	1	4	Houses release button (06) and handle spring (25). The shaft of the umbrella (08) fits into a slot at the bottom of this part. A small notch at the top of this component keeps the release button (06) and rider (07) in proper alignment. A hole near bottom of component is location where the screw (04) attaches this component to the handle mechanism casing (03) and also to the shaft.	Plastic	Injection Molding
06	Release Button	1	4	Releases latch inside handle to allow shaft extension	Plastic	Injection Molding
07	Rider	1	11	Once pushed upward by user, activates arm mechanism	Acrylic	Injection Molding
08	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
09	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
10	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
11	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
12	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
13	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
14	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
15	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
16	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
17	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
18	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
19	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
20	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
21	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
22	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
23	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
24	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
25	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]
26	[Insert Name]	[Insert quantity]	[Insert mass]	[Insert function]	[Insert material]	[Insert Manufacturing process]

Analysis

Detailed Product Analysis

Design for Manufacturing & Assembly (DFMA)

Manufacturing

Assembly

Failure Mode Effects and Analysis (FMEA)

Design for Environment (DFE)

Energy Analysis

Green House Gases Analysis

Toxic Releases Analysis

Life Cycle Assessment (LCA)

DFE Analysis Conclusion

Team Member Roles

Figure 3. Group picture taken at MechE Lab

Lizmarie Comenencia: Team Leader

Conroy Brown: ???

David Carter: DFMA Leader

Dennis Ou: ???

Teja Shah: FMA Leader

Marcus Townsend: DFE Leader

References

1. Carnegie Mellon University Green Design Institute. (2012) Economic Input-Output Life Cycle Assessment (EIO-LCA) US 2002 (428) model [Internet], Available from: <http://www.eiolca.net/> [Accessed 15 September, 2012]

2. Dieter, George E., and Linda C. Schmidt. Engineering Design. 4th Edition. New York, NY: McGraw-Hill, 2009. 707-715. Print.

3. http://en.wikipedia.org/wiki/File:Parts_of_an_Umbrella.svg